Pump Wet Ends and Related Parts

This Kit is an 2HP Impeller for an Executive 48 Frame Wet End up to 2HP Motor and a 56 Frame Wet End 2 HP Motor. This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you...

This is a 2HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End 2HP Motor that has about 10.0 Amps on High Speed. This Impeller fits between the Face and the Volute of an Aqua-Flo FMHP, FMCP, FMVP, and...

This part is a face plate drain plug for Aqua-Flo pumps.. It does not come with an O-Ring you will find the link to that below.. Aqua-Flo Pump, Drain Plug, O-Ring Xp2, Xp2e, XP3, 7/16" ID, 3/32"  

This part is a 4 HP 56 Frame Waterway Executive 2" X 2" Wet End / Pump complete with Screws, Volute, Impeller, Seal, Face and the Wear Ring. The difference between a 48 or 56 Frame wet end is the spacing of the Motor Thru bolts. The 48 Frame will be 3...

This part is a Complete 1 1/2 HP 48 Frame Vico Wet End that is very unusual with the Heat Blanket Circulation Nipples.. It is 1 1/2" x 1 1/2" meaning it measures about 2 3/8" edge to edge on the threads.. Most wet end that look like this one measures 3"...

Vico Ultima/Ultra Flo Pump Impeller 230V 8.0A or 115V 12.0AClosed face impeller made for the Ultima and Ultra Flo spa pumps by Vico. Rated at 1.0hp, it is used in an Ultima and/or Ultra Flo pump wet end, and must be installed on a 1.0hp (or greater) thru...

 This part is the slinger found between the impeller and wet end and the shaft going into the pump motor bearing area and is designed to sling water away from the bearing in case of a seal leak at the wet end.. Note: It has to be placed on the motor...

You are buying (1) Bearing that fit some motors that are used in hot tubs, usually small 48 frame motors and some circulation pumps, this bearing is 15.9MM ID x 40MM OD. Some of the motors this fits are A.O.Smith/Regal Beloit, Century/Regal Beloit,...

This is a 3HP Impeller with a 2 1/8" Eye with 3/8" Vane Width and 4 3/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 3.0HP Motor which would have about 12.0A on high speed. This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 or FMXP2 Wet...

This Drain Plug fits Vico Ultima and Ultimax and comes without O-Ring.. If you need the O-Ring click the Link: Pump, Drain Plug, O-Ring, will fit most Drain Plugs

This Pump is a Complete Pump for Watkins Hot Spring Hot Tubs under the numbers 36746, 72194, 72197 with a Vendor Code 4081, Wavemaster 8000 or 8200... This pump is a 48Frame 230V 2 Speed with a 2.0 HP Wet End that features a 2" x 2" inlet and outlet Wet...

Standard Pump Union Adapter Assembly With this adapter you can convert a 2" Threaded Pump Union whcih measures about 3" I.D. to a 1 1/2" threaded fitting which = 1 7/8" O.D. standard wet end. An O-Ring does come with this fitting but if you just needed...