Shop

This is a 2HP Seal and Impeller Kit.. The Impeller has a 2 1/8" Eye width and 1/4" Vane width and 4 3/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 2.0HP Motor would be about 10.0 Amps on high speed at 230V or 16.0 Amps High Speed at 115V. This Impeller...

This part is a 45 Degree 2" Street X 2"Slip PVC Plumbing Fitting that has a Threaded hole for a Pressure Switch. The Union glues into a 2" fitting on one side and then receives the fitting on the other side. It will Glue into any 2" fitting to make a...

This Connect Kit is an Air Bleeder barbed plug, 3/8" X 3/8" Barbed Coupler, 4" of 3/8" Tubing and Silicon sealer usually used on a Waterway Hot Tub Pump Face to bleed the air off the pump while filling the tub up. I have seen these fittings in many...

This Part is a Wet End O-Ring for a 48 or 56 Frame Face Plate for a Jacuzzi Premium or Sundance WUA400 6500 Intertek LX Brand Pump Wet End only.. Watch the video for instruction on how to install this part and also how to determine if this...

This Parts is a NON-Standard 2" Heater or Pump Union O-Ring that measures 2 5/8" Center to Center. The O-Ring is 2 5/8" center to center and fits some unions but most unions are 2 1/2" center to center... Do not buy this O-Ring until you...

This part is a Tee that is 2"Slip x 3/4" FPT x 2" Slip.. This part is usually found in plumbing with spigot screwed into it.. Note there are 2 Spigot sizes 3/4" and 1/2" Threaded..

This part is a 3/4" Barb x 3/4" x 3/4" Barbed Tee used to couple 3/4" ID Tubing together. Other Parts Normally used with this part: Tubing 3/4" Inside Diameter 1" OD (1) Foot Used on Water Manifolds and More (2) Feet of Tubing 3/4" Inside Diameter...

This part is a 3/4" Barb x 3/8" x 3/4" Barbed Tee used to couple 3/4" ID and 3/8" ID Tubing together. Other Parts Normally used with this part: Tubing 3/4" Inside Diameter 1" OD (1) Foot Used on Water Manifolds and More (2) Feet of Tubing 3/4"...

This part is a 2" Center to Center O-Ring that fits some 1 1/2" Pump Unions that features a 2" groove. The O-Ring is 2" center to center and fits Magic Plastics 2" pump unions but there are exceptions which normally would be a 2 1/8" center to...

This Kit is a Barb Adapter, 3/4" Barb x 2" Spigot... that will glue inside of a 2" Slip Manifold or other 2" Slip fitting and is usually used to couple a 3/4" water tube back to the barb on the fitting.. Also Note: If you order a manifold kit that...

This Kit is a Barb Adapter, 3/4" Barb x 2" Spigot to 3/4" X 3/4" Barb Coupler Kit, Fits 2" Slip Water Manifolds that features (2) Clamps, 4" 3/4" ID Tubing and (1) 3/4" x 3/4" Barb coupler..  that will glue inside of a 2" Slip Manifold or other...

This 1" CMP Waterfall Control Plunger Replacement Kit that includes the Cap, Handle, PLunger Assembly and o-rings.. This kit is found in some 1" CMP Waterfall or Neck Jet Control valves.  NOTE: This Plunger looks a lot like the Waterway Brand...