Shop

This part is a 3/4" Barb x 3/4" x 3/4" Barbed Tee used to couple 3/4" ID Tubing together. Other Parts Normally used with this part: Tubing 3/4" Inside Diameter 1" OD (1) Foot Used on Water Manifolds and More (2) Feet of Tubing 3/4" Inside Diameter...

This part is a 3/4" Barb x 3/8" x 3/4" Barbed Tee used to couple 3/4" ID and 3/8" ID Tubing together. Other Parts Normally used with this part: Tubing 3/4" Inside Diameter 1" OD (1) Foot Used on Water Manifolds and More (2) Feet of Tubing 3/4"...

This part is a 2" Center to Center O-Ring that fits some 1 1/2" Pump Unions that features a 2" groove. The O-Ring is 2" center to center and fits Magic Plastics 2" pump unions but there are exceptions which normally would be a 2 1/8" center to...

This Kit is a Barb Adapter, 3/4" Barb x 2" Spigot... that will glue inside of a 2" Slip Manifold or other 2" Slip fitting and is usually used to couple a 3/4" water tube back to the barb on the fitting.. Also Note: If you order a manifold kit that...

This Kit is a Barb Adapter, 3/4" Barb x 2" Spigot to 3/4" X 3/4" Barb Coupler Kit, Fits 2" Slip Water Manifolds that features (2) Clamps, 4" 3/4" ID Tubing and (1) 3/4" x 3/4" Barb coupler..  that will glue inside of a 2" Slip Manifold or other...

This 1" CMP Waterfall Control Plunger Replacement Kit that includes the Cap, Handle, PLunger Assembly and o-rings.. This kit is found in some 1" CMP Waterfall or Neck Jet Control valves.  NOTE: This Plunger looks a lot like the Waterway Brand...

This part is a Gray 3 5/8" Handle Knob for a 4" Wide Sundance® 3 Way Spa Diverter Valve. This Item is the Handle Only. The Valve this parts fits is found on Sundance® Spas only!!  Compare the measurements to be sure this...

This part is a Single of Jumper Wire that would go from a standard heater element Electrode Tab to the board Relay Spade Connector.. Loop for the heater side to female spade.. These can be used on 4.0kw to 5.5kw elements.. Circuit Board...

This part is a Set of Jumper Wires that would go from a standard heater element Electrode Tab to the board Relay Spade Connector.. Loop for the heater side to female spade.. These can be used on 4.0kw to 5.5kw elements.. Circuit Board...

This part is a Reducing Tee that is 1-1/2" Slip x 1/2" Female Pipe Thread x 1-1/2" Slip... The 1 1/2" Sides receive pipe and fittings that would measures about 1 7/8" OD on each end and a 1/2" Female pipe thread 3/4" OD..

This Manifold is  1 1/2" input which measures 1 7/8" Inside Diameter x (4) 1" outputs that measure 1 1/4" Inside Diameter.  Note: These manifolds are new old stock so they will not be perfect aesthetically...   Barb/Port Size 1" ...

This part is a Reducing Tee that is 1-1/2" Slip x 1/2" Slip x 1-1/2" Slip... The 1 1/2" Sides receive pipe and fittings that would measures about 1 7/8" OD on each end and a 1/2" pipe or fitting that would measure about 3/4" OD..