Pump Wet Ends and Related Parts

This part is a 3HP Sta-Rite DJ Dura-Jet Pump Impeller.. This impeller will usually have the number 17400-0135 cast into the back and will measure about 4 1/8" wide with an eye width of 1 3/4" and a vane width of 1/2".. This can be found on motors with an...

This item is a 1.0HP Waterway HiFlo Pump Impeller "C".. If Your motor is 115V the amperage would be about 12 Amp if 230V it would be about 10 amps..Closed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 1...

This Connect Kit is an Air Bleeder barbed plug, 3/8" X 3/8" Barbed Coupler, 4" of 3/8" Tubing and Silicon sealer usually used on a Waterway Hot Tub Pump Face to bleed the air off the pump while filling the tub up. I have seen these fittings in many...

This Part is a Wet End O-Ring for a 48 or 56 Frame Face Plate for a Jacuzzi Premium or Sundance WUA400 6500 Intertek LX Brand Pump Wet End only.. Watch the video for instruction on how to install this part and also how to determine if this...

This Parts is a NON-Standard 2" Heater or Pump Union O-Ring that measures 2 5/8" Center to Center. The O-Ring is 2 5/8" center to center and fits some unions but most unions are 2 1/2" center to center... Do not buy this O-Ring until you...

This O-Ring  is used on Aqua-Flo Pump Drain Plugs on Xp2, Xp2e, XP3 pumps and more..  Part Type    O-RingCross Section    3/32"Inside Diameter    7/16"id 

This Seal Kit with bearing is used ONLY in Watkins HotSpring Caldera Wet Ends where the motor has the Vendor code of 3536. This kit features the seal, (1) bearing and an install tool as well as silicone to install the seal with.. It is 1 39/64" Across...

This Seal Kit is used ONLY in Watkins Hot Spring Caldera Wet Ends where the motor has the Vendor code of 3536. This kit features the seal and an install tool as well as silicone to install the seal with.. It is 1 39/64" Across the back of the Spring...

This Seal Set is used ONLY in Watkins HotSpring Caldera Wet Ends where the motor has the Vendor code of 3536. It is 1 39/64" Across the back of the Spring Seal part that goes into the volute or wetend back and the Ceramic & Rubber part that goes...

This Kit Fits Watkins, Vendor #4081, Wavemaster Pumps found under the name Wavemaster 6000, 7000, 8000, 8200, 9000, 9200 numbers Features (2) Bearings & (1) Seal for 4081 Pumps on Hotspring Watkins Hot Tubs and (1) 1/2Oz Tube of The Professor's Silly...

This is a Kit that features (1) PS-200 Seal and (2) Bearings that fit most motors that are mated to Aqua-Flo Pump Wet Ends as well as Waterway " Viper" Wet Ends, The Professor silly Juice to seal the seal. This Seal is used in Most Aqua-Flo Wet Ends...

This kit is a Kit that Fits Watkins, Vendor #4081, Wavemaster XP2 Pumps found under the name Wavemaster 6000, 7000, 8000, 8200, 9000, 9200 numbers Features (1) Seal for XP2 Pumps on Hotspring Watkins Hot Tubs and (1) 1/2Oz Tube of The Professor's Silly...