Shop

This part is a Waterway 1" Spa Hot Tub Air Control Valve with the hidden type cap to be used under a larger handle style cap. You use this valve to replace the guts of an installed valve and don't use the body.. The Valve Cap Width is approx. 2 11/16".....

This part is (1) Complete Threaded Coupler that is 2" Slip X 2"Slip. The Coupler receives a 2" fitting which measures 2 3/8" OD on one side and then receives a 2" fitting which measures 2 3/8" OD on the other side. The inside diameter...

This is the shortest Coupler or Coupling, 2" Slip x 2" Slip, Short measures 1 5/8" and is about 1 1/4" shorter than the normal coupling and 3/4" shorter than the middle size.. Note: This Coupler does not have as much surface for gluing so it will not...

This kit is a 3' Long RADKit® designed to go onto the outside of a 2" fitting and seal off the area between (2) 2" Fittings Outside to Outside.. An example would be if you had a Suction fitting dripping at the glue joint and there is a piece of 2"...

This is a XP2 1.5HP Seal & Impeller with a 2 1/8" Eye Width and a 5/16" Vane Width and 4" OD for an Aqua-Flo 48 or 56 Frame Wet End 1.5HP Motor that has about 9.0 Amps at 230V. This Impeller fits between the Face and the Volute of an...

This part is a Hot Tub Replacement Bottom Drain Inside Wall Fitting with a 3/4" slip fitting on each end which measures about 1" I.D.. This part is on the foam side of the tub and the Fitting screws into this fitting.. You have to stand the hot tub up...

This kits is a Waterway Viper Pump 5.0 Impeller, (2) Bearing, Seal, Install Tool and Silicone.. A Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 5HP pump impeller to be on a...

This kits is a Waterway Viper Pump 5.0 Impeller, (1) Bearing, Seal, Install Tool and Silicone.. A Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 5HP pump impeller to be on a...

This kits is a Waterway Viper Pump 5.0 Impeller, Seal, Install Tool and Silicone.. A Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 5HP pump impeller to be on a 14-16 amp motor.....

This kits is a Waterway Viper Pump 4.0 Impeller, (2) Bearing, Seal, Install Tool and Silicone.. A Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 4HP pump impeller to be on a 12amp...

This kits is a Waterway Viper Pump 4.0 Impeller, (1) Bearing, Seal, Install Tool and Silicone.. A Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 4HP pump impeller to be on a 12amp...

This kits is a Waterway Viper Pump 4.0 Impeller, Seal, Install Tool and Silicone.. A Waterway Viper pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 4HP pump impeller to be on a 12amp motor.....