Complete Wet Ends

This thru-bolt is 10-32 threads and 10-3/4" Long and has a 5/16" Bolt head.. It fits some Intertek Guangdong LX 56fr motors only.. Motor Brand    Intertek Guangdong LX 56frMotor Parts Type    Thru-BoltPart...

This Face Plate O-Ring Is 5 1/8" Inside Diameter and is 1/8" Thick. It is found on Aqua-Flo 1 1/2" x 1 1/2" (Which Measures 2 3/8" Outside of the threads on the Sunction and Pressure Side of the Wet End) These Wet Ends used the names Flo-Master,...

This Kit is a 3/8" Tubing Connection Kit for 3/8" Plumbing repairs where you are connecting old 3/8" Clear Tubing that measures about 1/2" OD between a cut air control line and the 3/8" Barb on an Air Manifold or Jet Body Air connection.. The kit...

  This part is a SWIM56-15 5 Horse Power 56 Frame Pump Bleeder with Silicone & Wet End fits Power-Rite Guangdong LX Brand SWIM56-15 Pump Motors only. These pumps usually have the part number Swim56-15 on the label. Watch the video...

For the bleeder barb for this wet end Click Here: Barbed Bleeder Plug for Guangdong LX 48 Frame Wet End Fine Threads Jacuzzi® or Sundance This part is aSWIM56-15 5 Horse Power 56 Frame Pump Wet End fits Power-Rite Guangdong LX Brand SWIM56-15...

This is a Watkins Wavemaster 9000 or 9200 2.5HP Seal Kit & Impeller with a 2 1/8" Eye Width. This Impeller fits between the Face and the Volute of a XP2 Wet End found on some Watkins Hot Spring Caldera pumps with Vendor Code 4081. ...

This part is an Air Bleeder barbed plug and O-Ring for Jacuzzi and Sundance Piranah Pump Faces Only.. Hot Tub Pump Faces to bleed the air off the pump while filling the tub up.  This barb is usually replaced because the barb is broken off and...

NOTE: There are 48 and 56 Frame verison of these wet ends so be sure you check yours before ordering.. The difference is the position of the thru bolts of the motor and the size of the motor it mounts to.. The 48 Frame version measures 3 5/8" in a...

NOTE: There are 48 and 56 Frame verison of these wet ends so be sure you check yours before ordering.. The difference is the position of the thru bolts of the motor and the size of the motor it mounts to.. The 48 Frame version measures 3 5/8" in a...

NOTE: There are 48 and 56 Frame verison of these wet ends so be sure you check yours before ordering.. The difference is the position of the thru bolts of the motor and the size of the motor it mounts to.. The 48 Frame version measures 3 5/8" in a...

This is a 1/15th HP Impeller for an Aqua-Flo Circulation Pump 48 Frame Side or Center Discharge CMHP, CMCP and FMVP Series Wet End. This Impeller fits between the Face and the Volute of an Aqua-Flo CMHP, CMCP and FMVP Series Wet End. I would advise...

Waterway Hi-Flo Wet EndSide discharge, 2"mbt suction/discharge, 48 frame wet end for the Waterway Hi-Flo pump. This wet end is used with a 12.0 Amp 3.0hp, 48 frame, thru-bolt style motor. The motor used may be either a single or dual speed. The wet end...