Pump Wet Ends and Related Parts

Seal Plate for Vico Ultima pumps. Material Type    PlasticVolute to Seal Plate Mounting Type    4 Bolts 4 NutsVolute to Seal Plate Hole Spacing    4-3/8"Seal Plate to Motor Mounting Type    48...

This item is a 3/4HP Waterway HiFlo Pump Impeller "B".. If Your motor is 115V the amperage would be about 11 Amp if 230V it would be about 7 amps..Closed face impeller made for the Hi-Flo side discharge pump by Waterway Plastics. Rated at...

 Vico Ultima Ultra Flo or Ultra Jet Pump ImpellerClosed face impeller made for the Ultima and Ultra Flo spa pumps by Vico. Rated at 4.0hp,which is between 12 and 14 Amps.. it is used in an Ultima, Ultra Jet and/or Ultra Flo pump wet end, and must be...

This part is an Aqua-Flo XP2 Impeller for a 2.0HP Motor which would have an Amperage Rating of about 10.0Amps on High Speed at 230V and 16.0 Amps on High Speed at 115V... It will also be a 56Frame motor which would have a 5/16" head on the through bolts...

This is a .75HP or 3/4HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End .75HP Motor that has about 7.0 Amps on High Speed at 230V and 7-8.0 Amps at 115V. This Impeller fits between the Face and the...

Vico, Ultimax Pump ImpellerClosed face impeller made for the Ultimax spa pump by Vico. Rated at 3.0hp,which would be 8-10.0 Amps.. it is used in an Ultimax pump wet end, and must be installed on a 2.0hp (or greater) thru bolt motor.  Click here for...

This parts is an Executive 2 1/2" Mpt Threaded Face plate assembly (Which will measure about 3 11/16" Across the Threads) less the O-rings, Screws, Bleeder Plugs and other hardware needed to attach it to the volute..There is another version of the face...

Vico/Balboa Ultima/Ultra Flo Pump ImpellerClosed face impeller made for the Ultima and Ultra Flo spa pumps by Vico/Balboa. Rated at 1.5hp,which is between 8 and 9 Amps.. it is used in an Ultima and/or Ultra Flo pump wet end, and must be installed on a 1...

This part is No Longer Available if you need a face you will have to choose a complete wet end..  Note: Due to a design change in the current XP2/XP2e pump wet ends, face plate or volute replacement is not suggested. Instead, replace the wet end to...

This part is an Aqua-Flo XP2 Impeller for a 4.0HP Motor which would have an Amperage Rating of about 14.0Amps on High Speed at 230V and Not applicable for 115V Pumps... It will also be a 56Frame motor which would have a 5/16" head on the through bolts.....

  This is a 1HP Impeller with a 2 1/8" Eye with 1/4" Vane Width and 3 7/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 1.0HP Motor would be about 8.0 Amps on high speed at 230V or 12.0 Amps at 115V. This Impeller fits between the Face and the Volute...

This part is a Wear Ring for a Hi-Flo Impeller found in Waterway Hi-Flo pumps only.. The Inside Diameter of the wear ring is 1 13/16"...