Pump Wet Ends and Related Parts

This Wavemaster 5000 Face Plate O-Ring Is 5 1/8" Inside Diameter and is 1/8" Thick.   The below List is other parts related to this Part: Watkins, Wavemaster 5000, Vendor Code 4081, Shaft Seal Kit, Silicon & Tool Buna Watkins, Wavemaster 5000,...

This Wavemaster 3000 Face Plate O-Ring Is 5 1/8" Inside Diameter and is 1/8" Thick.   For other parts related to this part see the below links:

This part is a replacement wear ring for Wavemaster 5000 Pump Impellers with a 1 3/4" Eye.. The ring measures about 1 3/4" inside the wear ring and 2 3/16" at the widest part and about 3/4" tall..   The below List is other parts related to this...

This part is a replacement wear ring for Wavemaster 3000 Pump Impellers with a 1 3/4" Eye.. The ring measures about 1 3/4" inside the wear ring and 2 3/16" at the widest part and about 3/4" tall.. For Other related parts see the below links:  ...

This is a 1HP Impeller for a Wavemaster 3000 Code 04184 48 Frame Side Discharge pump. This Impeller fits between the Face and the Volute of a Wavemaster 3000 Series Wet End. I would advise replacing the Seal when you replace the Impeller. This Impeller...

This kit is a that Fits Watkins, Vendor #04184, found under the name Wavemaster 3000 numbers Features (1) Seal, seal tool (2) Bearings and (1) 1/2 Oz Tube of The Professor's Silly Juice a Specially Formulated for Hot Tubs Silicon Sealer.   Note:...

This kit is a that Fits Watkins, Vendor #04184, found under the name Wavemaster 3000 numbers Features (1) Seal, seal tool (1) Bearing and (1) 1/2 Oz Tube of The Professor's Silly Juice a Specially Formulated for Hot Tubs Silicon Sealer.   Note:...

This kit is a that Fits Watkins, Vendor #04184, found under the name Wavemaster 3000 numbers Features (1) Seal, seal tool and (1) 1/2 Oz Tube of The Professor's Silly Juice a Specially Formulated for Hot Tubs Silicon Sealer.   Note: Watkins used...

Watkins Vendor Code 4081 Wavemaster, 4000, 6000, 7000, 8000, 8200, 9000, 9200... 48Frame Pump Face O-Ring Only fits around the Face of this Pump Face...  

This Part is a 2 1/8" wear ring that is used between the impeller and the wet end face on Watkins Vendor Code # 4081, Wavemaster, 4000, 6000, 7000, 8000, 8200, 9000, 9200.. This wear ring serves as a seal between the suction and pressure sides of the...

  This is a 1HP Seal & Impeller Kit for a Watkins 37334 Vendor Code# 4081 Pump with a 2 1/8" Eye with 1/4" Vane Width and 3 7/8" OD for an Wavemaster 48 1.0HP Motor would be about 7-8.0 Amps on high speed at 230V or 11-12.0 Amps at...

This part is a 3HP Sta-Rite DJ Dura-Jet Pump Impeller.. This impeller will usually have the number 17400-0135 cast into the back and will measure about 4 1/8" wide with an eye width of 1 3/4" and a vane width of 1/2".. This can be found on motors with an...