Pump Wet Ends and Related Parts

This Kit is an 2HP Impeller for an Executive 48 Frame Wet End up to 2HP Motor and a 56 Frame Wet End 2 HP Motor. This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you...

This is a 2HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End 2HP Motor that has about 10.0 Amps on High Speed. This Impeller fits between the Face and the Volute of an Aqua-Flo FMHP, FMCP, FMVP, and...

This part is a face plate drain plug for Aqua-Flo pumps.. It does not come with an O-Ring you will find the link to that below.. Aqua-Flo Pump, Drain Plug, O-Ring Xp2, Xp2e, XP3, 7/16" ID, 3/32"  

 This part is the slinger found between the impeller and wet end and the shaft going into the pump motor bearing area and is designed to sling water away from the bearing in case of a seal leak at the wet end.. Note: It has to be placed on the motor...

You are buying (1) Bearing that fit some motors that are used in hot tubs, usually small 48 frame motors and some circulation pumps, this bearing is 15.9MM ID x 40MM OD. Some of the motors this fits are A.O.Smith/Regal Beloit, Century/Regal Beloit,...

This is a 3HP Impeller with a 2 1/8" Eye with 3/8" Vane Width and 4 3/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 3.0HP Motor which would have about 12.0A on high speed. This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 or FMXP2 Wet...

This Drain Plug fits Vico Ultima and Ultimax and comes without O-Ring.. If you need the O-Ring click the Link: Pump, Drain Plug, O-Ring, will fit most Drain Plugs

Standard Pump Union Adapter Assembly With this adapter you can convert a 2" Threaded Pump Union whcih measures about 3" I.D. to a 1 1/2" threaded fitting which = 1 7/8" O.D. standard wet end. An O-Ring does come with this fitting but if you just needed...

This part is an Jacuzzi J Pump Impeller Wear Ring.. It measures about 1 15/16" ID and 2 7/16" to the outermost OD..  Fits the following pumps: Cygnet Series - All Horsepowers J, JCM, K and KM Series - All Horsepowers L, LC, LCUN2, LT, LX,...

This part is a Bleeder Barb that is 3/8" barb x 1/4" Threaded MPT fitting fits Wet End Face Bleeder Plug Holes to attach a Bleeder Line it fits Waterway Executive 48 & 56 Frame Parts & Wetends, Power-Right 9089X, 9094X,...

This part is a Pump Bleeder Barb with O-Ring that is found on some Aqua-Flo Xp2 and Xp2e wet ends but is used with an unusual bleeder line.. The line is 1/4" Inside Diameter not 3/8" Inside Diameter like most bleeder lines.. This part does come with the...

This part is an O-Ring that is a square style.. It fits Piranha "A", Thera-Flo, Thera-Max, Bracketless, all found on Jacuzzi, Sundance, Hotspring and other brands as well...Part Type    Square RingO Reference Number  ...