Shop

This Face Plate O-Ring Is 5 1/8" Inside Diameter and is 1/8" Thick. It is found on Aqua-Flo 1 1/2" x 1 1/2" (Which Measures 2 3/8" Outside of the threads on the Sunction and Pressure Side of the Wet End) These Wet Ends used the names Flo-Master,...

Drain Plug with O-Ring for Waterway Wet Ends Fits Executive, Viper, Hi- Flo, Iron Might, Spa Flo, Supreme, Mustang, Workman and More  We also offer the 3/8" Barb that replaces these plug in the case of using a Pump Bleeder System... This are found...

This Wear Ring only fits Waterway Executive 4 or 5HP Impellers for a 48 or 56 Frame Pump Wet Ends and measures 13/16" thick from front to back or some Intertek impellers... If you have a Waterway Executive 1,2 or 3 Horsepower Wet End it will require...

You are buying on a 4.0KW Titanium Heater Element.  This Heater Element features the bend in the back of the element needed to fit the Balboa M-7 heater tubes. This also fits Gecko, ACC, Spa Guts, Spa Builders Len Gordon, Brett Aqualine,...

This part is a Pump Motor Starter Capacitor.. it is a 88-108 MFD or Microfarad.. 250V   This capacitor measures 1-13/16"diameter x 3-3/8" Long  Special Technical Note: The Capacitor is sometimes the cause of your motor not operating but often...

This is a .5HP or 1/2HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End .5HP Motor that has about 6.0 Amps on High Speed at 230V and 6-7.0 Amps at 115V. This Impeller fits between the Face and the...

(25) Tubing Clamps, Fits Tubing 3/8" I.D. x 1/2"O.D., Double Wire, for Air System Manifolds, Jet Bodies, Pump Bleeders and other items that 3/8" Barbs..  Links to related parts: (1) Tubing Clamp, Fits Tubing 3/8" I.D. x 1/2"O.D., Double Wire, for...

(1) Tubing Clamp, Fits Tubing 3/8" I.D. x 1/2"O.D., Double Wire, for Air System Manifolds, Jet Bodies, Pump Bleeders and other items that 3/8" Barbs..  Self-compensating hose clamp expands/contracts with temperature change Cannot be over/under...

This part is a Universal Air Bleeder 1/4" Mpt X 3/8" Barb plug usually used on Hot Tub Pump Faces to bleed the air off the pump while filling the tub up. I have seen these fittings in many brands of Hot Tubs just compare the pictures and measurements...

This Kit is a Air Bleeder 1/4" Mpt X 3/8" Barb plug and Silicon sealer usually used on Hot Tub Pump Faces to bleed the air off the pump while filling the tub up. I have seen these fittings in many brands of Hot Tubs just compare the pictures and...

This part is a Air Bleeder barbed plug usually used on a Aqua-Flo and CMP Hot Tub Pump Faces to bleed the air off the pump while filling the tub up. I have seen these fittings in many brands of Hot Tubs just compare the pictures and measurements with...

This kit is a Air Bleeder barbed plug and Silicon sealer usually used on a Aqua-Flo and CMP Hot Tub Pump Faces to bleed the air off the pump while filling the tub up. I have seen these fittings in many brands of Hot Tubs just compare the pictures and...