Plumbing and Related Parts

This kit is a 3' Long RADKit® designed to go onto the outside of a 2" fitting and seal off the area between (2) 2" Fittings Outside to Outside.. An example would be if you had a Suction fitting dripping at the glue joint and there is a piece of 2"...

This part is a Hot Tub Replacement Bottom Drain Inside Wall Fitting with a 3/4" slip fitting on each end which measures about 1" I.D.. This part is on the foam side of the tub and the Fitting screws into this fitting.. You have to stand the hot tub up...

This part is a (1) 90 Ell 1 1/2" Street X 1 1/2"Slip with an 1/8" FPT hole in the side.. The 90 ELL receives a 1 1/2" fitting on one side which would measure 1 7/8" OD and then slips into a 1 1/2" fitting on the other side that would measure 1 7/8" ID on...

This part is a 2" Slip x 2" Street 90 Elbow w/thermowell fitting, 5/16" t-well, 90° ell pvc... The 2" fitting measure about 2 3/8" ID on the slip side and 2 3/8" OD on the street side..   PVC Pipe Fitting Type Ell, 90 deg w/t-well Heater...

The part is a 1" x 3/4" - 3/4" Wye.. Manifold Wye

This part is no longer available.. But we have a solution.. The RENU Kit is a 1" x 3/4" - 3/4" Wye with reducer bushings 1" to 3/4" and 3/4" to 1/2" Along with related parts to make RENU Connections to old Flex pipe.. On the 3/4" Side it comes with a...

This part is no longer available.. But we have a solution.. The Kit is a 1" x 3/4" - 3/4" Wye with reducer bushings 1" to 3/4" and 3/4" to 1/2".. These bushings also make it easier to Spin It to Win It. Manifold Wye

This Kit is a 3/4" Spin To Win Glue Kit for 3/4" Plumbing repairs where you are connecting old 3/4" Plumbing that measures about 1" OD to new plumbing.. The kit includes a 6" Piece of 3/4" Flex Pipe that measures about 1" OD and a 3/4" Coupler and (1)...

This part is a 3/4" Spin To Win Kit for 3/4" Plumbing repairs where you are connecting old 3/4" Plumbing that measures about 1" OD to new plumbing.. The kit includes a 6" Piece of 3/4" Flex Pipe that measures about 1" OD and a 3/4" Coupler.. This type...

This part is a 45 Degree 2" Street X 2"Slip PVC Plumbing Fitting that has a Threaded hole for a Pressure Switch. The Union glues into a 2" fitting on one side and then receives the fitting on the other side. It will Glue into any 2" fitting to make a...

This Connect Kit is an Air Bleeder barbed plug, 3/8" X 3/8" Barbed Coupler, 4" of 3/8" Tubing and Silicon sealer usually used on a Waterway Hot Tub Pump Face to bleed the air off the pump while filling the tub up. I have seen these fittings in many...

This part is a Tee that is 2"Slip x 3/4" FPT x 2" Slip.. This part is usually found in plumbing with spigot screwed into it.. Note there are 2 Spigot sizes 3/4" and 1/2" Threaded..