Pumps and Related Parts

Grundfos Circulating Pump 115V with 1" Barbs... In my opinion this is a better pump than the Laing Brand... Spa Guy Note: If you are using this pump to convert from a Laing you will need this Conversion Kit If you want the same kit but need Glue Click...

This Seal Kit PS-3868 Seal is an Upgraded Better Viton Carbon Graphite Version of the PS-201 Seal used Primarily in Vico & Sta-Rite Wetends.It is 1 3/8" Across the back of the Spring Seal part that goes onto the Impeller and the Ceramic & Rubber...

This part is a Salt/Ozone resitant PS-3865 which is the upgraded Better version Viton Carbon Graphite version of the PS-1000 Seal. This Seal is used Primarily in Waterway Brand Wet Ends. It is 1 3/8" Across the back of the Spring Seal part that goes...

This Seal is a Salt/Ozone resistant PS-3867 which is the Better - Viton Carbon Graphite version of the PS-200 Seal used Primarily in Aqua-Flo Wet Ends and Waterway "Viper" Wet Ends. It is 1 1/4" Across the back of the Spring Seal part that goes onto...

This part is a 1 1/2" Pump Union Split Nut Repair Kit which includes the split nut and (2) Screws for use with a 1 1/2" Pump Union. The Pump Union Split Nut that measures about 2 7/8" on the outside and mounts to the existing Pump Union Body using 2...

This part is a Gasket Heater Union Mo-Flo, 2" ID x 2-3/4" OD Cal Spa with a 2-5/8" Center to Center Small Lip.. The Lip is about 2-5/8" Center to Center but is really thin and tiny meaning the other style gasket with a thick 2-5/8" lip will not work.. ...

This part is a 1 1/2" Slip X 1 1/2" Pump Union with Gasket or Oring that matches Union. The Union receives a 1 1/2" pipe or fitting on one side and then Screws to a 1 1/2" Wet end(Pump) Threaded Part on the...

This O-Ring is 5 1/8" Inside Diameter and 3/16" wide and is used in many applications for Wet Ends between the Face and Volute or under a Trap Lid brands include Hayward, PacFab, Pentair, Sta-Rite in these series Dura-Jet DJ Series Wet End Faces, Dynamo,...

This part is a 2 1/2" Pump Union Gasket Only for use with a 2 1/2" Pump Union that would measure about 3 5/8" Inside Threads. This gasket measures 3 1/4" O.D. x 2 3/8" I.D. and the lip is 2 7/8" center to center. This version is the 4th most...

You are buying a Air Bleeder barbed plug usually used on Hot Tub Pump Faces to bleed the air off the pump while filling the tub up. I have seen these fittings in many brands of Hot Tubs just compare the pictures and measurements with your current fitting...

This part is (1) Bearing that fit most motors that are used in hot tubs, this bearing is 17MM ID.. Some of the motors this fits are A.O.Smith/Regal Beloit, Century/Regal Beloit, Franklin Electric, General Electric NOTE: Installing bearings requires...

NOTE: This gasket does not fit your Coleman SALUSPA DO NOT order it.. Click this link to see Saluspa Gaskets.. Saluspa This part is a Standard 1 1/2" Heater or Pump Union Gasket. The gasket is 2 3/8" across and fits unions that have a 1...