Pump Wet Ends and Related Parts

Aqua-Flo Xp2 Flo-Master 48Frame Pump Face O-Ring Only fits around the Face of a Xp Pump Face exclusively for An Aqua-Flo Xp 48 frame pump which has 2" inlet and outlet which measures about 3" across the threads... If you have a Xp2 56frame 6.1" or 6'3"...

This Kit is an 4HP Impeller for an Executive 48 Frame Wet End up to 4HP Motor and a 56 Frame Wet End 4HP Motor. This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you replace...

This Seal Kit PS-3868 Seal is an Upgraded Better Viton Carbon Graphite Version of the PS-201 Seal used Primarily in Vico & Sta-Rite Wetends.It is 1 3/8" Across the back of the Spring Seal part that goes onto the Impeller and the Ceramic & Rubber...

This part is a Salt/Ozone resitant PS-3865 which is the upgraded Better version Viton Carbon Graphite version of the PS-1000 Seal. This Seal is used Primarily in Waterway Brand Wet Ends. It is 1 3/8" Across the back of the Spring Seal part that goes...

This Seal is a Salt/Ozone resistant PS-3867 which is the Better - Viton Carbon Graphite version of the PS-200 Seal used Primarily in Aqua-Flo Wet Ends and Waterway "Viper" Wet Ends. It is 1 1/4" Across the back of the Spring Seal part that goes onto...

This part is a 1 1/2" Pump Union Split Nut Repair Kit which includes the split nut and (2) Screws for use with a 1 1/2" Pump Union. The Pump Union Split Nut that measures about 2 7/8" on the outside and mounts to the existing Pump Union Body using 2...

This part is a 1 1/2" Slip X 1 1/2" Pump Union with Gasket or Oring that matches Union. The Union receives a 1 1/2" pipe or fitting on one side and then Screws to a 1 1/2" Wet end(Pump) Threaded Part on the...

This O-Ring is 5 1/8" Inside Diameter and 3/16" wide and is used in many applications for Wet Ends between the Face and Volute or under a Trap Lid brands include Hayward, PacFab, Pentair, Sta-Rite in these series Dura-Jet DJ Series Wet End Faces, Dynamo,...

This part is a 2 1/2" Pump Union Gasket Only for use with a 2 1/2" Pump Union that would measure about 3 5/8" Inside Threads. This gasket measures 3 1/4" O.D. x 2 3/8" I.D. and the lip is 2 7/8" center to center. This version is the 4th most...

You are buying a Air Bleeder barbed plug usually used on Hot Tub Pump Faces to bleed the air off the pump while filling the tub up. I have seen these fittings in many brands of Hot Tubs just compare the pictures and measurements with your current fitting...

NOTE: This gasket does not fit your Coleman SALUSPA DO NOT order it.. Click this link to see Saluspa Gaskets.. Saluspa This part is a Standard 1 1/2" Heater or Pump Union Gasket. The gasket is 2 3/8" across and fits unions that have a 1...

This part is a 2" Slip X 2" Threaded Pump Union with Gasket or O-ring that matches Union. The Union recieves a 2" pipe or fitting on one side and then Screws to a 2" Wetend(Pump) Threaded Part on the other...