Pump Wet Ends and Related Parts

This Kit is an 5HP Impeller for an Executive 48 Frame Wet End up to 5HP Motor and a 56 Frame Wet End 5HP Motor. This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you replace...

This is a 1.5HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End 1.5HP Motor that has about 9.0 Amps on High Speed at 230V and 14.0 Amps at 115V. This Impeller fits between the Face and the Volute of...

This is a 2.5HP Impeller with a 2 1/8" Eye width and 5/16" Vane width and 4" OD for anAqua-Flo 48 or 56 Frame Wet End 2.5HP Motor that is about 11.0 Amps on High Speed. This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 or FMXP2 Wet...

This item is a 2 1/8" wear ring that is used between the impeller and the wet end face on Aqua-Flo XP or XP2 Pumps. This wear ring is for all Horse Powers on 48 or 56 frame XP2 Wet Ends. This wear ring serves as a seal between the suction and pressure...

This is a 1.5HP Impeller with a 2 1/8" Eye Width and a 5/16" Vane Width and 4" OD for an Aqua-Flo 48 or 56 Frame Wet End 1.5HP Motor that has about 9.0 Amps at 230V. This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 or FMXP2 Wet End...

This part is a 2 1/2" Pump Union Split Nut Repair Kit which includes the split nut and (2) Screws for use with a 2 1/2" Pump Union. The Pump Union Split Nut that measures about 3 3/4" on the outside and mounts to the existing Pump Union Body using 2...

This is a 1HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End 1HP Motor that has about 8.0 Amps on High Speed. This Impeller fits between the Face and the Volute of an Aqua-Flo FMHP, FMCP, FMVP, and...

This is a 2HP Impeller with a 2 1/8" Eye width and 1/4" Vane width and 4 3/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 2.0HP Motor would be about 10.0 Amps on high speed at 230V or 16.0 Amps High Speed at 115V. This Impeller fits between the Face and...

This Kit is an 3HP Impeller for an Executive 48 Frame Wet End up to 3HP Motor and a 56 Frame Wet End 3HP Motor. This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you replace...

You are buying a Set of (2) 1 1/2" Slip X 1 1/2" Pump Unions with Gasket or Oring that matches Unions. The Union recieves a 1 1/2" pipe or fitting on one side and then Screws to a 1 1/2" Wetend(Pump) Threaded Part on the other side. It will Glue to a 1...

This item is a 1/4" Air Bleeder Plug with Thin threads that can be found on the New style of a StaRite Dura-Jet DJ Series, Dyna-Glas/Dynamax, ABG, Dyna-Jet, TPE, Some StaRite Pool Multiports, Petair/ Pacfab Sand Filter systems and more. Note: This is not...

This item is a 1/4" Air Bleeder Plug with coarse threads that can be found on the old style of a StaRite Dura-Jet DJ Series Wetends only. The head of this plug will break off and leave the threads in the wet end face. You can take a flat screw driver and...