Shop

This part is a (1 or 2) Speed 56 Frame Complete Intertek Pump that fits Jacuzzi Premium brand Hot Tubs. These pumps usually have the part number WUA-400-II, and then 6500-352 or 6500-365 or 6500-367, or 6500-363 on the label. It is about 7 1/4"" across...

This part is a Clip that hold the  Jacuzzi Spa Trap, Mesh Skimmer Bag into place inside the filter housing. Fits most J-300 Series, 2002 and newer and here is a link to the filter for this tub too Jacuzzi Premium 2002+ Filter Skimmer Bag has 6 holes...

This item is a Gray Complete Suction Fitting that requires a 3 3/8" hole... The cover is 5 3/16" Wide... The plumbing size is 2" which would measure about 2 3/8" Outside Diameter of the pipe that glues in.. If your plumbing is 1 1/2" you would need a 2"...

This is a 5-1/4" FLUIDIX-INTELLI-JET WITH ESCUTCHEON for Sundance Hot Tubs.. This jet is very specific to Sundance brand hot tubs only do not order for another brand.. Please Look closely at the pictures with measurements to be sure before ordering....

This Filter is a 40 Square Foot Filter Cartridge for a Dynasty Hot Tub that is 6" Outside Diameter x 8 1/4" in Length. It has a 1 1/2" SAE Threaded Fitting which is a Thick Thread that measures about 2" outside diameter of the threads. SAE Threads are...

This is a 4HP Seal, (2) Bearing and Impeller Kit.. The Impeller has a 2 1/8" Eye width and 1/2" Vane width and 4 1/2" OD for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor would be about 14.0 Amps on high speed at 230V. This Impeller fits between the...

This is a 4HP Seal, (1) Bearing and Impeller Kit.. The Impeller has a 2 1/8" Eye width and 1/2" Vane width and 4 1/2" OD for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor would be about 14.0 Amps on high speed at 230V. This Impeller fits between the...

You are buying a Kit that features (1) PS-200 Seal and (2) Bearings that fit most motors that are mated to Aqua-Flo Pump Wet Ends as well as Waterway " Viper" Wet Ends, The Professor silly Juice to seal the seal. This Seal is used in Most Aqua-Flo...

This part is a Complete CMP Bottom Drain Suction that is VGB Comaptible and requires a 3 5/16" Hole..  Suction Fitting Complete    Complete Assembly, StraightHole Size    3-5/16"Cover Diameter  ...

NOTE: This part is obsolete but we do have an alternative camp that will work but it is Dark Graphite Gray. If you order this Teardrop cap you will get the 6 spoke cap instead.. This part is a Cal Spa 1" Spa Hot Tub Air...

Dimensions 3-1/4”x7”This TSC-8/K-8 control panel will work with most MSPA systems, has 10 buttons including filtration cycle and Economy mode buttons, and will control three pumps and an air blower. It has an LCD display and comes with a 10ft...

This item is a NEW Old Stock Jet body that fits Waterway Jumbo Jets that have 7 1/2" Faces.. The water connections are (2) 1 1/2" Slip Waters on either side and the air connections are 1" Slip on each side. New Old Stock. Part is discontinued. But we...