Bath Garden Tub Pumps & Related Parts

This pump is a Waterway Genesis Generation Energy Efficient Bath Pump 5.5 amps 115 Volts w/Air Switch The Plumbing connections are 1 1/2" on the Pressure and Suction sides which measure about 2 3/8" across the threads.. There are two barbed fittings on...

This pump is a Wow High Performance Pump with 1 1/2" x 1 1/2" connections that measure about 2 3/8" across the threads.. It is a .75HP 115V 5.5Amp pump with an Air Switch and Cord.. This Vico-Ultrajet range of Hydro-Massage Whirlpool Pumps have been...

Gemini Plus II Pump Complete with Wet End and Air Switch... 1 1/2" X 1 1/2" which measures about 2 3/8" across the threads.. Specifications are 1.5 HP 115Volt 12.5Amps... For high flow bath jet systems Length = 12-11/16" Width = 5-11/16" Discharge...

This part is a 100 ft roll of Air Tubing 1/8" Inside Diameter is used with Air Buttons, Air Button Style Topsides and Air Switch Applications and between Garden Tub Pumps and Air Button Switches... Air Tubing Inside Diameter 1/8" Tubing Type Air ...

This part is an Air Switch, Tecmark, TBS 339, SPNO, 25 Amp, Threaded, Latching.. Wire connects are 5/16" male quick connect Spade Type tabs and required panel hole is 5/8"..25 AmpSingle Pole Normally OpenLatching Style Switch Note: The Nut Style can vary...

3/4" Water X 1/2" Air This complete Jacuzzi BMH jet includes a plumbing kit. The plumbing kit includes: 1" x 3/4" 90° reducer 1-1/2" x 1-1/2" x 3/4" tee 3/4" 90° 3/4" tee 3/4" street 90° 3/4" 45° 1/2" street 90° 1/2" coupling 1/2"...

Gemini Plus II Pump Complete with wet end and Air Switch... 1 1/2" X 1 1/2" which measures about 2 3/8" across the threads.. Specifications are .75 HP 115Volt 8.5Amps... For high flow bath jet systems Length = 12-11/16" Width = 5-11/16" Discharge...

You are buying (1) Bearing that fit some motors that are used in hot tubs, usually small 48 frame motors and some circulation pumps, this bearing is 15.9MM ID x 40MM OD. Some of the motors this fits are A.O.Smith/Regal Beloit, Century/Regal Beloit,...

Standard Pump Union Adapter Assembly With this adapter you can convert a 2" Threaded Pump Union whcih measures about 3" I.D. to a 1 1/2" threaded fitting which = 1 7/8" O.D. standard wet end. An O-Ring does come with this fitting but if you just needed...

This part is (1) 1/8" X 1/8" Barbed Coupler that fits 1/8" OD , 3/16" ID Clear Hose on each side. These are used for connecting Clear Hoses together in Hot Tubs or pools and commonly used in Air Button Switch systems.

You are buying a Set of (2) 1 1/2" Slip X 1 1/2" Pump Unions with Gasket or Oring that matches Unions. The Union recieves a 1 1/2" pipe or fitting on one side and then Screws to a 1 1/2" Wetend(Pump) Threaded Part on the other side. It will Glue to a 1...

This part is a latching Style Single Pole Dual Throw Switch 20 Amp Hole Through Mount with 1/8" Spout air connector and the Wire connects are 5/16" male quick connect tabs and required panel hole is 5/8". This switch is the standard or Universal...