HTPOFAmerica

3HP 2-Speed 230V LX Intertek Spa Pump 56Frame 2"x2" WUA-300-II WP-300-II LP-300-II Video Guide

(No reviews yet) Write a Review
SKU:
ASP56WUA300-II
Shipping:
Calculated at Checkout
  • Spa Hot Tub 56Fr intertek LX Pumps 2" X 2" 3HP 2 Speed 230V WUA Video How To
  • Compare your screws to be sure that this is the correct wet end.
  • Spa Hot Tub 56Fr intertek LX Pumps 2" X 2" 3HP 2 Speed 230V WUA Video How To 2" Suction Side measures 3" across the threads..
  • The original pump looks like this...
  • Spa Hot Tub 56Fr intertek LX Pumps 2" X 2" 3HP 2 Speed 230V WUA Video How To 2" Pressure Side measures 3" across the threads..
  • Compare your wet end to this picture to be sure that this is the correct wet end.
  • Compare your motor shaft to these to be sure...
  • Spa Hot Tub 56Fr intertek LX Pumps 2" X 2" 3HP 2 Speed 230V WUA Video How To
  • Spa Hot Tub 56Fr intertek LX Pumps 2" X 2" 3HP 2 Speed 230V WUA Video How To
  • When putting your cord back on the new pump note C= Common or the White Wire, L= Low Speed and is usually the Black Wire and rarely the Red Wire, H=High Speed and is usually the Red Wire but occasionally the Black, Green = Ground or the Green wire. They way you can tell if you have it wired correctly is when you power up the pump should go into Low Speed First. If it goes into High Speed you need to power down and reverse the red & black wires and power back up and verify it goes into Low Speed first. If you leave it wrong it will overheat and damage the Hot Tub especially during warm weather...
  • When putting your cord back on the new pump note C= Common or the White Wire, L= Low Speed and is usually the Black Wire and rarely the Red Wire, H=High Speed and is usually the Red Wire but occasionally the Black, Green = Ground or the Green wire. They way you can tell if you have it wired correctly is when you power up the pump should go into Low Speed First. If it goes into High Speed you need to power down and reverse the red & black wires and power back up and verify it goes into Low Speed first. If you leave it wrong it will overheat and damage the Hot Tub especially during warm weather...
  • Spa Hot Tub 56Fr intertek LX Pumps 2" X 2" 3HP 2 Speed 230V WUA Video How To
  • Spa Hot Tub 56Fr intertek LX Pumps 2" X 2" 3HP 2 Speed 230V WUA Video How To
  • Spa Hot Tub 56Fr intertek LX Pumps 2" X 2" 3HP 2 Speed 230V WUA Video How To
  • Spa Hot Tub 56Fr intertek LX Pumps 2" X 2" 3HP 2 Speed 230V WUA Video How To
$379.99

Description

This complete 56 Frame spa circulation pump delivers 3 Horse Power at 10.0/3.5 Amp with dual speed operation and features genuine Intertek LX manufacturing. Common part numbers found on the label include WUA-300-II, WP-300-II, and LP-300-II. Refer to the instructional video for proper pump identification techniques and compatibility verification guidance. Physical dimensions: approximately 7 1/4" diameter across the pump face, 7 3/8" height measured from bottom to top of volute pressure side, and 15" depth from rear to front edge. Both inlet and outlet connections are designated 2" x 2" thread fittings, with actual measurement of 3" across from thread edge to thread edge.

IMPORTANT COMPATIBILITY NOTE: This pump design shares similar appearance with Aqua-Flo and CMP pump models and can serve as a direct replacement when swapping the complete pump assembly.

Original wet end configuration with Bleeder Barb feature: If your existing wet end includes a bleeder barb and the bleeder screw heads accept a flat screwdriver, verify these specifications match before installation.

View AllClose

Related Products

Related Products