HTPOFAmerica

4.0HP Intertek LX Spa Pump 230V 1-Speed 56Fr 2"x2" WUA-400-I LP-400-I WP-400-I

(No reviews yet) Write a Review
SKU:
ASP56WUA400-I
Shipping:
Calculated at Checkout
  • Spa Hot Tub 56Fr Intertek LX Pumps 2" X 2" 4.0HP 1 Speed 230V WUA Video How To
  • Compare your screws to be sure that this is the correct wet end.
  • Compare your wet end to this picture to be sure that this is the correct wet end.
  • The original pump looks like this...
  • Spa Hot Tub 56Fr Intertek LX Pumps 2" X 2" 4.0HP 1 Speed 230V WUA Video How To 2" Suction Side measures 3" across the threads..
  • Spa Hot Tub 56Fr Intertek LX Pumps 2" X 2" 4.0HP 1 Speed 230V WUA Video How To 2" Pressure Side measures 3" across the threads..
  • Compare your motor shaft to these to be sure...
  • When putting your cord back on the new pump note C= Common or the White Wire, L= Low Speed and is usually the Black Wire and rarely the Red Wire, H=High Speed and is usually the Red Wire but occasionally the Black, Green = Ground or the Green wire. They way you can tell if you have it wired correctly is when you power up the pump should go into Low Speed First. If it goes into High Speed you need to power down and reverse the red & black wires and power back up and verify it goes into Low Speed first. If you leave it wrong it will overheat and damage the Hot Tub especially during warm weather...
  • When putting your cord back on the new pump note C= Common or the White Wire, L= Low Speed and is usually the Black Wire and rarely the Red Wire, H=High Speed and is usually the Red Wire but occasionally the Black, Green = Ground or the Green wire. They way you can tell if you have it wired correctly is when you power up the pump should go into Low Speed First. If it goes into High Speed you need to power down and reverse the red & black wires and power back up and verify it goes into Low Speed first. If you leave it wrong it will overheat and damage the Hot Tub especially during warm weather...
  • Spa Hot Tub 56Fr Intertek LX Pumps 2" X 2" 4.0HP 1 Speed 230V WUA Video How To
  • Spa Hot Tub 56Fr Intertek LX Pumps 2" X 2" 4.0HP 1 Speed 230V WUA Video How To
  • Spa Hot Tub 56Fr Intertek LX Pumps 2" X 2" 4.0HP 1 Speed 230V WUA Video How To
  • Spa Hot Tub 56Fr Intertek LX Pumps 2" X 2" 4.0HP 1 Speed 230V WUA Video How To
  • Spa Hot Tub 56Fr Intertek LX Pumps 2" X 2" 4.0HP 1 Speed 230V WUA Video How To
$379.99

Description

Genuine 56 Frame Intertek LX Brand Complete Pump Unit - 4.0 Horsepower, 12.0 Amp, Single Speed, 230 Volt Configuration. This replacement pump is identified by part numbers WUA-400-I, WP-400-I, or LP-400-I printed on the manufacturer label. Refer to instructional video content to properly identify your existing pump and confirm correct fitment before ordering. Physical dimensions include approximately 7 1/4 inches across the pump face, roughly 7 3/8 inches measured from bottom to top of the volute pressure side, and 15 inches from rear to front edge. The 2" x 2" suction and pressure side threaded fittings measure 3 inches from thread edge to thread edge.

IMPORTANT COMPATIBILITY NOTE: This unit bears strong visual resemblance to Aqua-Flo and CMP pump models and will serve as a direct interchange when replacing the complete pump assembly.

If your existing wet end features a bleeder barb and the bleeder screw heads accommodate a flat screwdriver, this confirms proper compatibility.

View AllClose

Related Products

Related Products