HTPOFAmerica

Watkins LX 48 Frame Pump 1.5HP 2-Speed 115V 2"x2" | Part 37334-03 | Vendor Code 3536

(No reviews yet) Write a Review
SKU:
ASP48WUABEEBC-IIWatkins
Shipping:
Calculated at Checkout
  • LX Pump 2" X 2" 1.5HP 2 Speed 115V Watkins 37334-03 Vendor Code 3536
  • LX Pump 2" X 2" 1.5HP 2 Speed 115V Watkins 37334-03 Vendor Code 3536
  • Note: If your original Pump has this on the back with a hose attached none of my pumps will have that nor will they be able to accept this part from your old pump.. You will save 100's of dollars over the original pump with that attachment that is only used to put heat from the motor under the tub and I believe the motors stay cooler without that device and last longer..
  • Compare your screws to be sure that this is the correct wet end.
  • Note: If your original Pump has this on the back with a hose attached none of my pumps will have that nor will they be able to accept this part from your old pump.. You will save 100's of dollars over the original pump with that attachment that is only used to put heat from the motor under the tub and I believe the motors stay cooler without that device and last longer..
  • LX Pump 2" X 2" 1.5HP 2 Speed 115V Watkins 37334-03 Vendor Code 3536 2" Pressure Side measures 3" across the threads..
  • LX Pump 2" X 2" 1.5HP 2 Speed 115V Watkins 37334-03 Vendor Code 3536 2" Suction Side measures 3" across the threads..
  • When putting your cord back on the new pump note C= Common or the White Wire, L= Low Speed and is usually the Black Wire and rarely the Red Wire, H=High Speed and is usually the Red Wire but occasionally the Black, Green = Ground or the Green wire. They way you can tell if you have it wired correctly is when you power up the pump should go into Low Speed First. If it goes into High Speed you need to power down and reverse the red & black wires and power back up and verify it goes into Low Speed first. If you leave it wrong it will overheat and damage the Hot Tub especially during warm weather...
  • LX Pump 2" X 2" 1.5HP 2 Speed 115V Watkins 37334-03 Vendor Code 3536 When putting your cord back on the new pump note C= Common or the White Wire, L= Low Speed and is usually the Black Wire and rarely the Red Wire, H=High Speed and is usually the Red Wire but occasionally the Black, Green = Ground or the Green wire. They way you can tell if you have it wired correctly is when you power up the pump should go into Low Speed First. If it goes into High Speed you need to power down and reverse the red & black wires and power back up and verify it goes into Low Speed first. If you leave it wrong it will overheat and damage the Hot Tub especially during warm weather...
  • When putting your cord back on the new pump note C= Common or the White Wire, L= Low Speed and is usually the Black Wire and rarely the Red Wire, H=High Speed and is usually the Red Wire but occasionally the Black, Green = Ground or the Green wire. They way you can tell if you have it wired correctly is when you power up the pump should go into Low Speed First. If it goes into High Speed you need to power down and reverse the red & black wires and power back up and verify it goes into Low Speed first. If you leave it wrong it will overheat and damage the Hot Tub especially during warm weather...
  • LX Pump 2" X 2" 1.5HP 2 Speed 115V Watkins 37334-03 Vendor Code 3536
MSRP: $439.99
$399.99
— You save $40.00

Description

This dual-speed 48 Frame complete spa pump delivers 1.0 Horsepower at 10.3/3.8 Amp and carries Watkins Vendor Code 3536. Manufactured by LX, this genuine replacement typically displays part number 37334-03 on Watkins-branded versions.

Physical measurements include approximately 7 1/4" face diameter, 7 3/8" height from base to volute pressure side top, and 15" depth from rear to front edge. The inlet and outlet connections are designated 2" x 2" with actual thread-to-thread measurement of 3".

Overall Dimensions: 15-3/16"L x 8-7/16"W x 8-7/16"H

IMPORTANT: This unit shares design similarities with Aqua-Flo and CMP models and can be swapped as complete assemblies. Verify you're selecting the correct frame size—this 48 frame motor back measures under 6" across, while 56 frame versions exceed 6".

Bleeder Barb Compatibility Note: If your existing wet end features a bleeder barb with flat-head screwdriver slot bleeder screws, a replacement bleeder barb will be required. Wing nut style indicates newer barb design—replacement only necessary if damaged.

View AllClose

Related Products

Related Products