Shop

This Kit is a 3/4" Spin To Win Glue Kit for 3/4" Plumbing repairs where you are connecting old 3/4" Plumbing that measures about 1" OD to new plumbing.. The kit includes a 6" Piece of 3/4" Flex Pipe that measures about 1" OD and a 3/4" Coupler and (1)...

This part is a 3/4" Spin To Win Kit for 3/4" Plumbing repairs where you are connecting old 3/4" Plumbing that measures about 1" OD to new plumbing.. The kit includes a 6" Piece of 3/4" Flex Pipe that measures about 1" OD and a 3/4" Coupler.. This type...

This valve is No Longer Available.. This part is a Horizontal 2 1/4" Wide cap  1"slip x 1"slip x 1"slip Waterway Scalloped Spa Small Waterfall or Neck Jet Control Complete Assembly Gray Valve.  This Valve can be found on a few brands...

This part is a Set of (2) Replacement Gasket Only that measures about 1 1/4" Edge to Edge with a 5/8" Center Hole for the "B/C" Coupling on the air jet spa for all some Saluspa or Lay-Z-Spa AirJet™ Hot Tub models (Siena, Miami, Havana, Paris, Palm...

This part is a Replacement Gasket Only that measures about 1 1/4" Edge to Edge with a 5/8" Center Hole for the "B/C" Coupling on the air jet spa for all some Saluspa or Lay-Z-Spa AirJet™ Hot Tub models (Siena, Miami, Havana, Paris, Palm Springs Air...

This item is a 1.0HP Waterway HiFlo Pump Impeller "C" Kit which included the Seal Kit as well.. If Your motor is 115V the amperage would be about 12 Amp if 230V it would be about 8 amps..Closed face impeller made for the HiFlo side discharge...

This item is a 1.0HP Waterway HiFlo Pump Impeller "C".. If Your motor is 115V the amperage would be about 12 Amp if 230V it would be about 10 amps..Closed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 1...

This is a 2HP Seal and Impeller Kit.. The Impeller has a 2 1/8" Eye width and 1/4" Vane width and 4 3/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 2.0HP Motor would be about 10.0 Amps on high speed at 230V or 16.0 Amps High Speed at 115V. This Impeller...

This part is a 45 Degree 2" Street X 2"Slip PVC Plumbing Fitting that has a Threaded hole for a Pressure Switch. The Union glues into a 2" fitting on one side and then receives the fitting on the other side. It will Glue into any 2" fitting to make a...

This Connect Kit is an Air Bleeder barbed plug, 3/8" X 3/8" Barbed Coupler, 4" of 3/8" Tubing and Silicon sealer usually used on a Waterway Hot Tub Pump Face to bleed the air off the pump while filling the tub up. I have seen these fittings in many...

This Part is a Wet End O-Ring for a 48 or 56 Frame Face Plate for a Jacuzzi Premium or Sundance WUA400 6500 Intertek LX Brand Pump Wet End only.. Watch the video for instruction on how to install this part and also how to determine if this...

This Parts is a NON-Standard 2" Heater or Pump Union O-Ring that measures 2 5/8" Center to Center. The O-Ring is 2 5/8" center to center and fits some unions but most unions are 2 1/2" center to center... Do not buy this O-Ring until you...