Pump Impellers

This part is a 2.5HP Sta-Rite DJ Dura-Jet Pump Impeller.. This impeller will usually have the number 17400-0123 cast into the back and will measure about 3 3/4" wide with an eye width of 1 3/4" and a vane width of 1/2".. This can be found on motors with...

This is a 4HP Impeller with a 2 1/8" Eye a 1/2" Vane Width and a 4 1/2" OD for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor which would have about 14.0A on high speed. This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 or FMXP2 Wet...

Waterway HiFlo Pump ImpellerClosed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 2.0hp, it is used in a Waterway HiFlo pump wetend, and must be installed on a 2.0hp (or greater) thru bolt motor. Shaft seal sold...

This part is an Aqua-Flo XP2 Impeller for a 1.5HP Motor which would have an Amperage Rating of about 9.0Amps on High Speed... It will also be a 56Frame motor which would have a 5/16" head on the through bolts... If you have 1/4" head you probably need...

Vico/Balboa Ultima/Ultra Flo Pump ImpellerClosed face impeller made for the Ultima and Ultra Flo spa pumps by Vico/Balboa. Rated at 3/4hp, it is used in an Ultima and/or Ultra Flo pump wet end, and must be installed on a 3/4hp (or greater) thru bolt...

This part is an Impeller for a Sta-Rite DuraJet DJ Wet End that would be called 1.0hp-1.5HP, your motor should be 8.0-9.0Amp at 230V or 16.0 Amps at 115V.. The number on the back of the impeller will be 17400-0121 if you have a number on yours.. ...

This impeller is no longer available from the manufacturer but the one at this link wil work in its place: Impeller, Aqua-Flo, XP3, 4.0hp, For XP3 Pump 2 1/2" x 2 1/2" Wet End This part is a Waterway Viper Pump 4.0 Impeller exclusively for A Waterway...

This Impeller is obsolete but there is an Impeller that will work but there is only one choice and it will look different than your old impeller: Impeller, Vico Ultima Ultra Jet Flo,4.0hp,Black/Green/Red           Power-Right...

Waterway HiFlo Pump ImpellerClosed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 3.0hp, it is used in a Waterway HiFlo pump wetend, and must be installed on a 3.0hp (or greater) thru bolt motor. Shaft seal sold...

Vico/Balboa Ultimax Pump ImpellerClosed face impeller made for the Ultimax spa pump by Vico/Balboa. Rated at 4.0hp, it is used in an Ultimax pump wet end, and must be installed on a 4.0hp (or greater) thru bolt motor. Click the below links for the seals,...

 Vico/Balboa Ultima Ultra Flo or Ultra Jet Pump ImpellerClosed face impeller made for the Ultima and Ultra Flo spa pumps by Vico. Rated at 3.0hp,which is between 10 and 12 Amps.. it is used in an Ultima, Ultra Jet and/or Ultra Flo pump wet end, and...