Pump Impellers

This item is a 1.0HP Waterway HiFlo Pump Impeller "C".. If Your motor is 115V the amperage would be about 12 Amp if 230V it would be about 10 amps..Closed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 1...

This is a 2HP Seal and Impeller Kit.. The Impeller has a 2 1/8" Eye width and 1/4" Vane width and 4 3/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 2.0HP Motor would be about 10.0 Amps on high speed at 230V or 16.0 Amps High Speed at 115V. This Impeller...

This Part is a Wet End O-Ring for a 48 or 56 Frame Face Plate for a Jacuzzi Premium or Sundance WUA400 6500 Intertek LX Brand Pump Wet End only.. Watch the video for instruction on how to install this part and also how to determine if this...

This Parts is a NON-Standard 2" Heater or Pump Union O-Ring that measures 2 5/8" Center to Center. The O-Ring is 2 5/8" center to center and fits some unions but most unions are 2 1/2" center to center... Do not buy this O-Ring until you...

This complete pump and motor is a Watkins Wavemaster 7000 replacement, 36675, 71699, 115V or 230V, (1) Speed, 16.0Amp or 8.0Amp, 48 frame 2" x 2" XP2 pump and motor... The 2" inlet and outlet measure about 3" across the threads... Keep in mind if you...

// Read This Note First!! NOTE: This Part will NOT Fit Sundance® or Jacuzzi® Tubs with a Guangdong LX Wet End for internal parts of that wet end you already have click here Jacuzzi® & Sundance® LX...

This O-Ring  is used on Aqua-Flo Pump Drain Plugs on Xp2, Xp2e, XP3 pumps and more..  Part Type    O-RingCross Section    3/32"Inside Diameter    7/16"id 

This Seal Kit with bearing is used ONLY in Watkins HotSpring Caldera Wet Ends where the motor has the Vendor code of 3536. This kit features the seal, (1) bearing and an install tool as well as silicone to install the seal with.. It is 1 39/64" Across...

This Seal Kit is used ONLY in Watkins Hot Spring Caldera Wet Ends where the motor has the Vendor code of 3536. This kit features the seal and an install tool as well as silicone to install the seal with.. It is 1 39/64" Across the back of the Spring...

This Seal Set is used ONLY in Watkins HotSpring Caldera Wet Ends where the motor has the Vendor code of 3536. It is 1 39/64" Across the back of the Spring Seal part that goes into the volute or wetend back and the Ceramic & Rubber part that goes...

This Kit Fits Watkins, Vendor #4081, Wavemaster Pumps found under the name Wavemaster 6000, 7000, 8000, 8200, 9000, 9200 numbers Features (2) Bearings & (1) Seal for 4081 Pumps on Hotspring Watkins Hot Tubs and (1) 1/2Oz Tube of The Professor's Silly...

This is a Kit that features (1) PS-200 Seal and (2) Bearings that fit most motors that are mated to Aqua-Flo Pump Wet Ends as well as Waterway " Viper" Wet Ends, The Professor silly Juice to seal the seal. This Seal is used in Most Aqua-Flo Wet Ends...