Pump Wet Ends and Related Parts

This part is an Aqua-Flo XP3 Pump 3.0HP Impeller exclusively for an Aqua-Flo XP3 pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 3.0HP pump impeller to be on a 12amp motor... Click here for the...

This part is an Aqua-Flo XP3 Pump 2.5HP Impeller exclusively for an Aqua-Flo XP3 pump which has 2 1/2" inlet and outlet which measures about 3 9/16" across the threads...I have found this 2.5HP pump impeller to be on a 10-12amp motor... Click here for...

Waterway Hi-Flo Wet EndSide discharge, 2"mbt suction/discharge, 48 frame wet end for the Waterway Hi-Flo pump. This wet end is used with a 12.0 Amp 3.0hp, 48 frame, thru-bolt style motor. The motor used may be either a single or dual speed. The wet end...

This part is a Wear Ring that only fits Guangdong LX or LP Impellers for a 48 or 56 Frame Pump Wet Ends and measures 3/4" thick from front to back... WUA Pumps.. Note: When Replacing some original LX Pump faces the wear ring was built into the face....

This O-Ring is a replacement for the Square Gasket that is found in the Sundance, Jacuzzi, Thera-Max, Thera-Flo, 2" Flat Style O-Ring..  Heater Union Part Type    O-RingPart Type    O-RingO Reference Number  ...

As of 11/2024 Aqua-flo has started to send this pump with a capacitor bump in an odd spot that may affect your installation. In light of that we are now sending this pump assembly out as a separate 10.5 Amp motor and a genuine 2.5 HP XP2 wetend. You...

You are buying an Air Bleeder Mountable Bleeder Fitting with a removable plug, a 1/4" Mpt X 3/8" Barb plug. This style set up is is usually found in Dimension One Hot Tubs in the Filter area and other brands as well.. Note; The plug is not sold...

This is a 4HP Seal, (2) Bearing and Impeller Kit.. The Impeller has a 2 1/8" Eye width and 1/2" Vane width and 4 1/2" OD for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor would be about 14.0 Amps on high speed at 230V. This Impeller fits between the...

This is a 4HP Seal, (1) Bearing and Impeller Kit.. The Impeller has a 2 1/8" Eye width and 1/2" Vane width and 4 1/2" OD for an Aqua-Flo 48 or 56 Frame Wet End 4.0HP Motor would be about 14.0 Amps on high speed at 230V. This Impeller fits between the...

You are buying a Kit that features (1) PS-200 Seal and (2) Bearings that fit most motors that are mated to Aqua-Flo Pump Wet Ends as well as Waterway " Viper" Wet Ends, The Professor silly Juice to seal the seal. This Seal is used in Most Aqua-Flo...

This part is an Impeller for a 48fr Vico Ultima or Ultra Flo, 0.50hp, Jet or Circulation Pump... Closed face impeller made for the Ultima and Ultra Flo spa pumps by Vico/Balboa. Rated at 1/2hp, it is used in an Ultima and/or Ultra Flo pump wet end, and...

This part is a 2.0HP Impeller fits some Jacuzzi, Sundance or Watkins Thermax Wet Ends only and would be found on a motor that is about 8.0 to 10.0 Amps on a 230V motor..... It can be found under the Name Thera-Max or Thera-Flo and is found on Jacuzzi...