Pump Wet Ends and Related Parts

This O-Ring is 5 1/8" Inside Diameter and 3/16" wide and is used in many applications for Wet Ends between the Face and Volute or under a Trap Lid brands include Hayward, PacFab, Pentair, Sta-Rite in these series Dura-Jet DJ Series Wet End Faces, Dynamo,...

This part is a 2 1/2" Pump Union Gasket Only for use with a 2 1/2" Pump Union that would measure about 3 5/8" Inside Threads. This gasket measures 3 1/4" O.D. x 2 3/8" I.D. and the lip is 2 7/8" center to center. This version is the 4th most...

You are buying a Air Bleeder barbed plug usually used on Hot Tub Pump Faces to bleed the air off the pump while filling the tub up. I have seen these fittings in many brands of Hot Tubs just compare the pictures and measurements with your current fitting...

NOTE: This gasket does not fit your Coleman SALUSPA DO NOT order it.. Click this link to see Saluspa Gaskets.. Saluspa This part is a Standard 1 1/2" Heater or Pump Union Gasket. The gasket is 2 3/8" across and fits unions that have a 1...

This part is a 2" Slip X 2" Threaded Pump Union with Gasket or O-ring that matches Union. The Union recieves a 2" pipe or fitting on one side and then Screws to a 2" Wetend(Pump) Threaded Part on the other...

This Seal is a PS-201 Seal used Primarily in Vico & Sta-Rite Wet Ends..  It is 1 3/8" Across the back of the Spring Seal part that goes onto the Impeller and the Ceramic & Rubber part that goes into the Volute or Wet End Back is 1 3/8"...

You are buying a PS-1000 Seal only. This Seal is used Primarily in Waterway Brand Wet Ends. It is 1 3/8" Across the back of the Spring Seal part that goes into the volute or wetend back and the Ceramic & Rubber part that goes into the...

This part is a 2" Pump Union Split Nut Repair Kit which includes the split nut and (2) Screws for use with a 2" Pump Union. The Pump Union Split Nut that measures about 3" on the Inside of the Threaded Side and mounts to the existing Pump Union Body...

You are buying a Kit that Features (1) PS-200 Seal for Aqua-Flo Pumps. This Seal is Used Primarily in Aqua-Flo Wetends but is found in some other brands like a Waterway "Viper*" Wet End. Pump Seal Assy 5/8"Shaft, 1.218"Seal O.D., 1.250"Seal O.D. The...

This part is a Standard 2" Heater or Pump Union Gasket with a 2 1/2" Lip Center to Center. The gasket is 2 7/8" across on the outside the inside diameter is about 2 3/16" and the lip that fits into the union is 2 1/2" center to...

This Kit features a 5HP Impeller and 1000 Seal with Silicon and a Seal Install Tool that fits an Executive 48 Frame Wet End up to 5HP Motor and a 56 Frame Wet End 5HP Motor. This Impeller fits between the Face and the Volute of an...

This part is an Add On Air Bleeder kit featuring a Mountable Bleeder Fitting with a removable plug, a 1/4" Mpt X 3/8" Barb plug, (2) Clamps for each end of the tubing and 36" of Clear 3/8" ID and Silicon sealer..   This kit can be added if you...