Pump Impellers

 Vico Ultima Ultra Flo or Ultra Jet Pump ImpellerClosed face impeller made for the Ultima and Ultra Flo spa pumps by Vico. Rated at 4.0hp,which is between 12 and 14 Amps.. it is used in an Ultima, Ultra Jet and/or Ultra Flo pump wet end, and must be...

This part is an Aqua-Flo XP2 Impeller for a 2.0HP Motor which would have an Amperage Rating of about 10.0Amps on High Speed at 230V and 16.0 Amps on High Speed at 115V... It will also be a 56Frame motor which would have a 5/16" head on the through bolts...

This is a .75HP or 3/4HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End .75HP Motor that has about 7.0 Amps on High Speed at 230V and 7-8.0 Amps at 115V. This Impeller fits between the Face and the...

Vico, Ultimax Pump ImpellerClosed face impeller made for the Ultimax spa pump by Vico. Rated at 3.0hp,which would be 8-10.0 Amps.. it is used in an Ultimax pump wet end, and must be installed on a 2.0hp (or greater) thru bolt motor.  Click here for...

Vico/Balboa Ultima/Ultra Flo Pump ImpellerClosed face impeller made for the Ultima and Ultra Flo spa pumps by Vico/Balboa. Rated at 1.5hp,which is between 8 and 9 Amps.. it is used in an Ultima and/or Ultra Flo pump wet end, and must be installed on a 1...

This part is an Aqua-Flo XP2 Impeller for a 4.0HP Motor which would have an Amperage Rating of about 14.0Amps on High Speed at 230V and Not applicable for 115V Pumps... It will also be a 56Frame motor which would have a 5/16" head on the through bolts.....

  This is a 1HP Impeller with a 2 1/8" Eye with 1/4" Vane Width and 3 7/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 1.0HP Motor would be about 8.0 Amps on high speed at 230V or 12.0 Amps at 115V. This Impeller fits between the Face and the Volute...

This part is a Impeller, Jacuzzi, J Pump, 1.0hp, 48FR, J Series, JCM Series, K Series, KM Series.. This is found on a Wet End that has a face like I show in the Photo Section only..  Impeller Type Closed Face Impeller Diameter...

Waterway Hi-Flo Pump ImpellerClosed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 1.5hp, it is used in a Waterway Hi-Flo pump wet end, and must be installed on a 1.5hp (or greater) thru bolt motor. Shaft seal...

This impeller fits a Universal CMP Brand 3HP Wet End only and it requires a Special Seal that you will find a link to below.. This impeller may also have any of the following manufacturer part numbers stamped on the back: 27203-300-300, 27203-000-300, or...

This part is an Aqua-Flo XP2 Impeller for a 3.0HP Motor which would have an Amperage Rating of about 12.0Amps on High Speed at 230V and Not applicable 115V Pumps... It will also be a 56Frame motor which would have a 5/16" head on the through bolts... If...

This part is an Aqua-Flo XP2 Impeller for a 2.5HP Motor which would have an Amperage Rating of about 11.0Amps on High Speed at 230V and is Not Applicable for 115V Pumps... It will also be a 56Frame motor which would have a 5/16" head on the through...