Pump Impellers

This O-Ring is 5 1/8" Inside Diameter and 3/16" wide and is used in many applications for Wet Ends between the Face and Volute or under a Trap Lid brands include Hayward, PacFab, Pentair, Sta-Rite in these series Dura-Jet DJ Series Wet End Faces, Dynamo,...

This Seal is a PS-201 Seal used Primarily in Vico & Sta-Rite Wet Ends..  It is 1 3/8" Across the back of the Spring Seal part that goes onto the Impeller and the Ceramic & Rubber part that goes into the Volute or Wet End Back is 1 3/8"...

You are buying a PS-1000 Seal only. This Seal is used Primarily in Waterway Brand Wet Ends. It is 1 3/8" Across the back of the Spring Seal part that goes into the volute or wetend back and the Ceramic & Rubber part that goes into the...

This part is a 2" Pump Union Split Nut Repair Kit which includes the split nut and (2) Screws for use with a 2" Pump Union. The Pump Union Split Nut that measures about 3" on the Inside of the Threaded Side and mounts to the existing Pump Union Body...

You are buying a Kit that Features (1) PS-200 Seal for Aqua-Flo Pumps. This Seal is Used Primarily in Aqua-Flo Wetends but is found in some other brands like a Waterway "Viper*" Wet End. Pump Seal Assy 5/8"Shaft, 1.218"Seal O.D., 1.250"Seal O.D. The...

This part is a Standard 2" Heater or Pump Union Gasket with a 2 1/2" Lip Center to Center. The gasket is 2 7/8" across on the outside the inside diameter is about 2 3/16" and the lip that fits into the union is 2 1/2" center to...

This Kit features a 5HP Impeller and 1000 Seal with Silicon and a Seal Install Tool that fits an Executive 48 Frame Wet End up to 5HP Motor and a 56 Frame Wet End 5HP Motor. This Impeller fits between the Face and the Volute of an...

This is a 2HP Seal, (2) Bearing and Impeller Kit.. The Impeller has a 2 1/8" Eye width and 1/4" Vane width and 4 3/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 2.0HP Motor would be about 10.0 Amps on high speed at 230V or 16.0 Amps High Speed at 115V...

This is a 2HP Seal, (1) Bearing and Impeller Kit.. The Impeller has a 2 1/8" Eye width and 1/4" Vane width and 4 3/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 2.0HP Motor would be about 10.0 Amps on high speed at 230V or 16.0 Amps High Speed at 115V...

This is a Watkins Wavemaster 8000 or 8200 2.0HP Seal Kit & Impeller with a 2 1/8" Eye Width... This Impeller fits between the Face and the Volute of a XP2 Wet End found on some Watkins Hot Spring Caldera pumps with Vendor Code 4081. Impeller Type ...

This 1.5 Horse Power Impeller, (2) Bearings & Seal Kit fits a 48 Frame Pump Wet Ends manufactured by Guangdong LX Brand only. The pumps this Impeller, Bearing & Seal Kit fits usually have the part number WUA-150, WP-150 or LP-150 on the label...

This 1.5 Horse Power Impeller, (1) Bearing & Seal Kit fits a 48 Frame Pump Wet Ends manufactured by Guangdong LX Brand only. The pumps this Impeller, Bearing & Seal Kit fits usually have the part number WUA-150, WP-150 or LP-150 on the label...