Pump Impellers

This item is a 2 1/8" wear ring that is used between the impeller and the wet end face on Aqua-Flo XP or XP2 Pumps. This wear ring is for all Horse Powers on 48 or 56 frame XP2 Wet Ends. This wear ring serves as a seal between the suction and pressure...

This is a 1.5HP Impeller with a 2 1/8" Eye Width and a 5/16" Vane Width and 4" OD for an Aqua-Flo 48 or 56 Frame Wet End 1.5HP Motor that has about 9.0 Amps at 230V. This Impeller fits between the Face and the Volute of an Aqua-Flo XP2 or FMXP2 Wet End...

This is a 1HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End 1HP Motor that has about 8.0 Amps on High Speed. This Impeller fits between the Face and the Volute of an Aqua-Flo FMHP, FMCP, FMVP, and...

This is a 2HP Impeller with a 2 1/8" Eye width and 1/4" Vane width and 4 3/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 2.0HP Motor would be about 10.0 Amps on high speed at 230V or 16.0 Amps High Speed at 115V. This Impeller fits between the Face and...

This Kit is an 3HP Impeller for an Executive 48 Frame Wet End up to 3HP Motor and a 56 Frame Wet End 3HP Motor. This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you replace...

Aqua-Flo Xp2 Flo-Master 48Frame Pump Face O-Ring Only fits around the Face of a Xp Pump Face exclusively for An Aqua-Flo Xp 48 frame pump which has 2" inlet and outlet which measures about 3" across the threads... If you have a Xp2 56frame 6.1" or 6'3"...

This Kit is an 4HP Impeller for an Executive 48 Frame Wet End up to 4HP Motor and a 56 Frame Wet End 4HP Motor. This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you replace...

This Seal Kit PS-3868 Seal is an Upgraded Better Viton Carbon Graphite Version of the PS-201 Seal used Primarily in Vico & Sta-Rite Wetends.It is 1 3/8" Across the back of the Spring Seal part that goes onto the Impeller and the Ceramic & Rubber...

This part is a Salt/Ozone resitant PS-3865 which is the upgraded Better version Viton Carbon Graphite version of the PS-1000 Seal. This Seal is used Primarily in Waterway Brand Wet Ends. It is 1 3/8" Across the back of the Spring Seal part that goes...

This Seal is a Salt/Ozone resistant PS-3867 which is the Better - Viton Carbon Graphite version of the PS-200 Seal used Primarily in Aqua-Flo Wet Ends and Waterway "Viper" Wet Ends. It is 1 1/4" Across the back of the Spring Seal part that goes onto...

This O-Ring is 5 1/8" Inside Diameter and 3/16" wide and is used in many applications for Wet Ends between the Face and Volute or under a Trap Lid brands include Hayward, PacFab, Pentair, Sta-Rite in these series Dura-Jet DJ Series Wet End Faces, Dynamo,...

This Seal is a PS-201 Seal used Primarily in Vico & Sta-Rite Wet Ends..  It is 1 3/8" Across the back of the Spring Seal part that goes onto the Impeller and the Ceramic & Rubber part that goes into the Volute or Wet End Back is 1 3/8"...