Pumps and Related Parts

This Kit is a 45° 2" Pump Union To Plumbing Connect Kit found in many Dynasty Brand Hot Tubs. The Pump Union which measures about 3" Inside the threads glues into a 2" Slip X Slip 45° fitting on one side and then a 2" Slice Valve Glues...

This O-ring is used on some 1 1/2" Pump Union that measures 2 1/8" Center to Center of the o-ring groove.. Part Type    O-RingJet Part Type    Gasket/O-RingCross Section    1/8"Union Fitting...

This Kit is a Universal Air Bleeder Connect Kit with (1) 1/4" Mpt X 3/8" Barb Plug, (1) 3/8" x 3/8" Barb Coupler, (4") of 3/8" Clear Tubing and Silicon sealer usually used on Hot Tub Pump Faces to bleed the air off the pump while filling the tub up. I...

This kit is an Air Bleeder Barbed Plug Connect Kit that features a Barbed Plug that is 1/4" MPT x 3/8" Barb, (1) 3/8" x 3/8" Barbed Coupler, 4" of 3/8" clear tubing and Silicon sealer usually used on a Aqua-Flo and CMP Hot Tub Pump Faces to bleed the air...

This kit is a Set of (2) Air Bleeder barbed plugs,(2) 3/8" x 3/8" Barb couplers, (2) 4" long pieces of 3/8" Tubing and Silicon sealer usually used on a Dynasty Hot Tub with Waterway Hot Tub Pump Face to bleed the air off the pump while filling the tub up...

This kit is a Set of (2) Air Bleeder barbed plugs and Silicon sealer usually used on a Dynasty Hot Tub with Waterway Hot Tub Pump Face to bleed the air off the pump while filling the tub up. I have seen these fittings in many brands just compare the...

This part is a Replacement "A" Coupling for Water jet spa for all some Saluspa or Lay-Z-Spa AirJet™ Hot Tub models (Siena, Miami, Havana, Paris, Palm Springs Air Jet, New York, Vegas, Saint Tropez, Hawaii and Monaco). If the "A" Coupling...

This Part is a Barbed Bleeder Barb with O-Ring that fits New Style 48 or 56 Frame WUA Intertek LX Brand Pump Wet End that uses a fine thread bleeder plug.. Watch the video for instruction on how to install this part and also how to...

This part is a Complete CMHP 1/15th HP Aqua-Flo 1 1/2" x 1 1/2" (Which measures about 2 3/8" Across the Threads) Side discharge 48 frame wet end for CMHP pumps. This wet end is used with a 48 frame motor that would have about .6 Amps on High Speed on a...

This pump is a Vico 48 Frame 115V 1.0-1.5HP 2 Speed replacement pump.The connections on this pump are 2" x 2" which measures about 3" Edge to edge on the threads.. Spa Pump Features:   Voltage 115V, 60Hz High speed 11.9 Amps, low speed 3.5...

This Parts is a NON-Standard 2" Heater or Pump Union O-Ring that measures 2 5/8" Center to Center. The O-Ring is 2 5/8" center to center and fits some unions but most unions are 2 1/2" center to center... Do not buy this O-Ring until you...

This Parts is a NON-Standard 2" Heater or Pump Union O-Ring that measures 2 5/8" Center to Center. The O-Ring is 2 5/8" center to center and fits some unions but most unions are 2 1/2" center to center... Do not buy this O-Ring until you...