Pumps and Related Parts

Watkins Vendor Code 4081 Wavemaster, 4000, 6000, 7000, 8000, 8200, 9000, 9200... 48Frame Pump Face O-Ring Only fits around the Face of this Pump Face...  

This Part is a 2 1/8" wear ring that is used between the impeller and the wet end face on Watkins Vendor Code # 4081, Wavemaster, 4000, 6000, 7000, 8000, 8200, 9000, 9200.. This wear ring serves as a seal between the suction and pressure sides of the...

  This is a 1HP Seal & Impeller Kit for a Watkins 37334 Vendor Code# 4081 Pump with a 2 1/8" Eye with 1/4" Vane Width and 3 7/8" OD for an Wavemaster 48 1.0HP Motor would be about 7-8.0 Amps on high speed at 230V or 11-12.0 Amps at...

As of 11/2024 Aqua-flo has started to send this pump with a capacitor bump in an odd spot that may affect your installation. In light of that we are now sending this pump assembly out as a separate 10.5 Amp motor and a genuine 2.5 HP XP2 wetend...

This complete pump and motor is a Watkins Wavemaster 7000, 8000 or 9000 replacement, 39577 Code 06290, 115V or 230V, (1) Speed, 20.0Amp or 10.0Amp, 48 frame 2" x 2" XP2 pump and motor... The 2" inlet and outlet measure about 3" across the threads... Keep...

This part is a 3HP Sta-Rite DJ Dura-Jet Pump Impeller.. This impeller will usually have the number 17400-0135 cast into the back and will measure about 4 1/8" wide with an eye width of 1 3/4" and a vane width of 1/2".. This can be found on motors with an...

This item is a 1.0HP Waterway HiFlo Pump Impeller "C" Kit which included the Seal Kit as well.. If Your motor is 115V the amperage would be about 12 Amp if 230V it would be about 8 amps..Closed face impeller made for the HiFlo side discharge...

This item is a 1.0HP Waterway HiFlo Pump Impeller "C".. If Your motor is 115V the amperage would be about 12 Amp if 230V it would be about 10 amps..Closed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 1...

This is a 2HP Seal and Impeller Kit.. The Impeller has a 2 1/8" Eye width and 1/4" Vane width and 4 3/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 2.0HP Motor would be about 10.0 Amps on high speed at 230V or 16.0 Amps High Speed at 115V. This Impeller...

This Connect Kit is an Air Bleeder barbed plug, 3/8" X 3/8" Barbed Coupler, 4" of 3/8" Tubing and Silicon sealer usually used on a Waterway Hot Tub Pump Face to bleed the air off the pump while filling the tub up. I have seen these fittings in many...

This Part is a Wet End O-Ring for a 48 or 56 Frame Face Plate for a Jacuzzi Premium or Sundance WUA400 6500 Intertek LX Brand Pump Wet End only.. Watch the video for instruction on how to install this part and also how to determine if this...

This Parts is a NON-Standard 2" Heater or Pump Union O-Ring that measures 2 5/8" Center to Center. The O-Ring is 2 5/8" center to center and fits some unions but most unions are 2 1/2" center to center... Do not buy this O-Ring until you...