HTPOFAmerica

3HP 230V Intertek LX Hot Tub Pump 56Fr 2"x2" Single Speed WUA-300-I WP-300-I LP-300-I

(No reviews yet) Write a Review
SKU:
ASP56WUA300-I
Shipping:
Calculated at Checkout
  • Spa Hot Tub 56Fr Intertek LX Pumps 2" X 2" 3HP 1 Speed 230V WUA Video How To
  • Compare your screws to be sure that this is the correct wet end.
  • The original pump looks like this...
  • Compare your wet end to this picture to be sure that this is the correct wet end.
  • Spa Hot Tub 56Fr Intertek LX Pumps 2" X 2" 3HP 1 Speed 230V WUA Video How To 2" Suction Side measures 3" across the threads..
  • Spa Hot Tub 56Fr Intertek LX Pumps 2" X 2" 3HP 1 Speed 230V WUA Video How To 2" Pressure Side measures 3" across the threads..
  • Compare your motor shaft to these to be sure...
  • When putting your cord back on the new pump note C= Common or the White Wire, L= Low Speed and is usually the Black Wire and rarely the Red Wire, H=High Speed and is usually the Red Wire but occasionally the Black, Green = Ground or the Green wire. They way you can tell if you have it wired correctly is when you power up the pump should go into Low Speed First. If it goes into High Speed you need to power down and reverse the red & black wires and power back up and verify it goes into Low Speed first. If you leave it wrong it will overheat and damage the Hot Tub especially during warm weather...
  • When putting your cord back on the new pump note C= Common or the White Wire, L= Low Speed and is usually the Black Wire and rarely the Red Wire, H=High Speed and is usually the Red Wire but occasionally the Black, Green = Ground or the Green wire. They way you can tell if you have it wired correctly is when you power up the pump should go into Low Speed First. If it goes into High Speed you need to power down and reverse the red & black wires and power back up and verify it goes into Low Speed first. If you leave it wrong it will overheat and damage the Hot Tub especially during warm weather...
  • Spa Hot Tub 56Fr Intertek LX Pumps 2" X 2" 3HP 1 Speed 230V WUA Video How To
  • Spa Hot Tub 56Fr Intertek LX Pumps 2" X 2" 3HP 1 Speed 230V WUA Video How To
  • Spa Hot Tub 56Fr Intertek LX Pumps 2" X 2" 3HP 1 Speed 230V WUA Video How To
  • Spa Hot Tub 56Fr Intertek LX Pumps 2" X 2" 3HP 1 Speed 230V WUA Video How To
  • Spa Hot Tub 56Fr Intertek LX Pumps 2" X 2" 3HP 1 Speed 230V WUA Video How To
$389.99

Description

This complete 3 Horse Power 10.0 Amp single speed 56 Frame circulation pump is manufactured by Intertek LX. Common label designations include WUA-300-I, WP-300-I, or LP-300-I part numbers. Please verify pump identification and compatibility using the specifications below to ensure proper fit. Physical dimensions: approximately 7 1/4" across pump face, 7 3/8" measured from bottom to top of volute pressure side, and 15" from rear to front edge. Both suction and pressure side thread fittings are designated 2" x 2" but actually measure 3" from thread edge to thread edge.

IMPORTANT: This pump design closely resembles Aqua-Flo and CMP pumps and complete units are interchangeable when replacing entire assembly.

If your existing wet end features a bleeder barb and the bleeder screw heads accommodate a flat screwdriver, this replacement will maintain the same configuration.

View AllClose

Related Products

Related Products