Jet Pumps, Complete

This part is a 2" Pump Union Split Nut Repair Kit which includes the split nut and (2) Screws for use with a 2" Pump Union. The Pump Union Split Nut that measures about 3" on the Inside of the Threaded Side and mounts to the existing Pump Union Body...

This part is a Standard 2" Heater or Pump Union Gasket with a 2 1/2" Lip Center to Center. The gasket is 2 7/8" across on the outside the inside diameter is about 2 3/16" and the lip that fits into the union is 2 1/2" center to...

This pump is a Jacuzzi J-Pump .75 HP, 48 frame 230V, Single Speed with a J Pump Style Wet End  that measures about 2 15/16" across the threads on both the suction and pressure side connections..  Note: This Pump will Only Work in Jacuzzi J Pump...

This pump is a Sundance or Jacuzzi Premium 45 Degree 48 frame 230V 2 Speed with a 2" x 2" Wet End  that measures about 3" across the threads.. The amperage is 10.7 Amps on high speed and 3.2 Amps on low speed and this pump will work as a one or...

This part is an Add On Air Bleeder kit featuring a Mountable Bleeder Fitting with a removable plug, a 1/4" Mpt X 3/8" Barb plug, (2) Clamps for each end of the tubing and 36" of Clear 3/8" ID and Silicon sealer..   This kit can be added if you...

This Parts is a NON-Standard 2" Heater or Pump Union Gasket with a 2 5/8" Center to Center Lip. The gasket is 2 7/8" across on the outside the inside diameter is about 2" and the lip that fits into the union is 2 5/8" center to...

This is a Watkins Wavemaster 8000 or 8200 2.0HP Seal Kit & Impeller with a 2 1/8" Eye Width... This Impeller fits between the Face and the Volute of a XP2 Wet End found on some Watkins Hot Spring Caldera pumps with Vendor Code 4081. Impeller Type ...

This Part is an Old Style Barbed Bleeder Plug that fits some 48 or 56 Frame WUA Intertek LX Brand Pump Wet Ends that use coarse thread bleeder plugs be sure to compare your old plugs to the pictures.. Watch the video for instruction on...

This 1.0 Horse Power 10.3/3.8 Amp (2) Speed 48 Frame Complete Pump is a Watkins Vendor Code 3536 LX Brand Pump. These pumps usually have the part number 37334-03 on the label for a Watkins Version.  It is about 7 1/4"" across the face of the pump,...

This is a 1.5-1.65HP Seal Kit & Impeller for Watkins, Vendor # 4081, Wavemaster, 4000, 6000 Pumps. This Impeller fits between the Face and the Volute of a the Wet End found on some Watkins HotSpring Caldera pumps with Vendor Code 4081 with Numbers...

Drain Plug with O-Ring for Waterway Wet Ends Fits Executive, Viper, Hi- Flo, Iron Might, Spa Flo, Supreme, Mustang, Workman and More  We also offer the 3/8" Barb that replaces these plug in the case of using a Pump Bleeder System... This are found...

This part is a Universal Air Bleeder 1/4" Mpt X 3/8" Barb plug usually used on Hot Tub Pump Faces to bleed the air off the pump while filling the tub up. I have seen these fittings in many brands of Hot Tubs just compare the pictures and measurements...