Shop

This is a 1HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End 1HP Motor that has about 8.0 Amps on High Speed. This Impeller fits between the Face and the Volute of an Aqua-Flo FMHP, FMCP, FMVP, and...

This is a 2HP Impeller with a 2 1/8" Eye width and 1/4" Vane width and 4 3/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 2.0HP Motor would be about 10.0 Amps on high speed at 230V or 16.0 Amps High Speed at 115V. This Impeller fits between the Face and...

This item is Thread Sealer Tape used to seal threads on items like Pressure Switches and Pressure Gauges. Teflon 1/2" X 520"

This Kit is an 3HP Impeller for an Executive 48 Frame Wet End up to 3HP Motor and a 56 Frame Wet End 3HP Motor. This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you replace...

This is a plug used to plug off a 3/8" ID Tube. It wil glue and slip inside of the hose to plug it off. We offer many different plugs based on the brand of manifold.

This part is (1) 1/8" X 1/8" Barbed Coupler that fits 1/8" OD , 3/16" ID Clear Hose on each side. These are used for connecting Clear Hoses together in Hot Tubs or pools and commonly used in Air Button Switch systems.

You are buying a Set of (2) 1 1/2" Slip X 1 1/2" Pump Unions with Gasket or Oring that matches Unions. The Union recieves a 1 1/2" pipe or fitting on one side and then Screws to a 1 1/2" Wetend(Pump) Threaded Part on the other side. It will Glue to a 1...

You are buying a 2" Slip X 2" Slip X (4) 1/2" Ports Manifold open style. This part used in tubs where 1/2" softpipe which measures 3/4" OD glues inside the ports and goes to the back of each jet in the tub and 2" Pipe which is 2 3/8" OD is plumb into 2"...

This part is (1) 1/4" X 3/8" Barbed Coupler that fits 3/8" OD , 1/4" ID Clear Hose on one side and 1/2" OD , 3/8" ID on the other side. These are used for connecting Clear Hoses together in Hot Tubs or pools and commonly used in Ozone systems.

You are buying on a 1 1/2" Slip X 1 1/2" Slip Slice Gate Valve. The Valve recieves a 1 1/2" pipe or fitting (Which is about 1 7/8" outside diameter) on each side. This part is used in hot tubs to stop the water so you could service the heater or the pump...

This part is a Set of (2) 2" Slip X 2" Pump Union with Gasket or O-ring that matches Union.   The Union recieves a 2" pipe or fitting on one side and then Screws to a 2" Wetend(Pump) Threaded Part on...

This part is a 2" Slip X 2" Slip X (6) 3/4" Slip Ports Manifold open Flow Through style. This part used in tubs where 3/4" softpipe which is 1" OD glues inside the ports which are 1" ID and goes to the back of each jet in the tub and 2" Pipe which is 2...