Pumps and Related Parts

This is a 2HP Impeller for an Aqua-Flo 48 Frame Side or Center Discharge FMHP, FMCP, FMVP, and TMCP Series Wet End 2HP Motor that has about 10.0 Amps on High Speed. This Impeller fits between the Face and the Volute of an Aqua-Flo FMHP, FMCP, FMVP, and...

Start Capacitor1-7/16"dia x 2-3/4"hgt

This Listing is for a Waterway Executive 56fr 2 Speed 230V 3 HP 2 1/2" X 2" Pump. Your sticker may say 4HP but based on the chart it is really a 3HP at 12 Amps. This unit features a 2" X 2" Executive Wet End that can be moved from the 12 O'clock...

This part is an Air Switch, Tecmark, TBS 339, SPNO, 25 Amp, Threaded, Latching.. Wire connects are 5/16" male quick connect Spade Type tabs and required panel hole is 5/8"..25 AmpSingle Pole Normally OpenLatching Style Switch Note: The Nut Style can vary...

3/4" Water X 1/2" Air This complete Jacuzzi BMH jet includes a plumbing kit. The plumbing kit includes: 1" x 3/4" 90° reducer 1-1/2" x 1-1/2" x 3/4" tee 3/4" 90° 3/4" tee 3/4" street 90° 3/4" 45° 1/2" street 90° 1/2" coupling 1/2"...

This part is a face plate drain plug for Aqua-Flo pumps.. It does not come with an O-Ring you will find the link to that below.. Aqua-Flo Pump, Drain Plug, O-Ring Xp2, Xp2e, XP3, 7/16" ID, 3/32"  

This part is a 4 HP 56 Frame Waterway Executive 2" X 2" Wet End / Pump complete with Screws, Volute, Impeller, Seal, Face and the Wear Ring. The difference between a 48 or 56 Frame wet end is the spacing of the Motor Thru bolts. The 48 Frame will be 3...

This part is a Complete 1 1/2 HP 48 Frame Vico Wet End that is very unusual with the Heat Blanket Circulation Nipples.. It is 1 1/2" x 1 1/2" meaning it measures about 2 3/8" edge to edge on the threads.. Most wet end that look like this one measures 3"...

Gemini Plus II Pump Complete with wet end and Air Switch... 1 1/2" X 1 1/2" which measures about 2 3/8" across the threads.. Specifications are .75 HP 115Volt 8.5Amps... For high flow bath jet systems Length = 12-11/16" Width = 5-11/16" Discharge...

Vico Ultima/Ultra Flo Pump Impeller 230V 8.0A or 115V 12.0AClosed face impeller made for the Ultima and Ultra Flo spa pumps by Vico. Rated at 1.0hp, it is used in an Ultima and/or Ultra Flo pump wet end, and must be installed on a 1.0hp (or greater) thru...

 This part is the slinger found between the impeller and wet end and the shaft going into the pump motor bearing area and is designed to sling water away from the bearing in case of a seal leak at the wet end.. Note: It has to be placed on the motor...

You are buying (1) Bearing that fit some motors that are used in hot tubs, usually small 48 frame motors and some circulation pumps, this bearing is 15.9MM ID x 40MM OD. Some of the motors this fits are A.O.Smith/Regal Beloit, Century/Regal Beloit,...