Pump Wet Ends and Related Parts

This item is a 1.0HP Waterway HiFlo Pump Impeller "C".. If Your motor is 115V the amperage would be about 12 Amp if 230V it would be about 10 amps..Closed face impeller made for the HiFlo side discharge pump by Waterway Plastics. Rated at 1...

This is a 2HP Seal and Impeller Kit.. The Impeller has a 2 1/8" Eye width and 1/4" Vane width and 4 3/8" OD for an Aqua-Flo 48 or 56 Frame Wet End 2.0HP Motor would be about 10.0 Amps on high speed at 230V or 16.0 Amps High Speed at 115V. This Impeller...

This Connect Kit is an Air Bleeder barbed plug, 3/8" X 3/8" Barbed Coupler, 4" of 3/8" Tubing and Silicon sealer usually used on a Waterway Hot Tub Pump Face to bleed the air off the pump while filling the tub up. I have seen these fittings in many...

This Part is a Wet End O-Ring for a 48 or 56 Frame Face Plate for a Jacuzzi Premium or Sundance WUA400 6500 Intertek LX Brand Pump Wet End only.. Watch the video for instruction on how to install this part and also how to determine if this...

This Parts is a NON-Standard 2" Heater or Pump Union O-Ring that measures 2 5/8" Center to Center. The O-Ring is 2 5/8" center to center and fits some unions but most unions are 2 1/2" center to center... Do not buy this O-Ring until you...

This item is a 48 Frame Vico Wet End with 2" x 2" inlet and outlet that would measure about 3" across the threads and it has a 3.0HP impeller which would fit a motor that has 10.0-12.0 amps at 230V and there are no 115V motors this fits.. Pump to Motor...

This part is a Sta-Rite Dura-Jet Complete 2" X 2" Wet End that fits both 48 or 56 frame motors and would fit a 230V Pump that is 8.0 Amps or a 115V pump that is 12.0 Amps.. The 2" fitting actually measures about 3" Edge to Edge across the threads.. It...

This complete pump and motor is a Watkins Wavemaster 7000 replacement, 36675, 71699, 115V or 230V, (1) Speed, 16.0Amp or 8.0Amp, 48 frame 2" x 2" XP2 pump and motor... The 2" inlet and outlet measure about 3" across the threads... Keep in mind if you...

Waterway Hi-Flo Wet EndSide discharge, 2"mbt suction/discharge, 48 frame wet end for the Waterway Hi-Flo pump. This wet end is used with a 11.0 Amp 2.0hp, 48 frame, thru-bolt style motor. The motor used may be either a single or dual speed. The wet end...

// Read This Note First!! NOTE: This Part will NOT Fit Sundance® or Jacuzzi® Tubs with a Guangdong LX Wet End for internal parts of that wet end you already have click here Jacuzzi® & Sundance® LX...

This O-Ring  is used on Aqua-Flo Pump Drain Plugs on Xp2, Xp2e, XP3 pumps and more..  Part Type    O-RingCross Section    3/32"Inside Diameter    7/16"id 

This Wet End is a 2" x 2" 1.5HP 48 or 56 frame Ultimax Vico® that would normally be found an a 230V pump with 9.0 Amps High speed or 14.0 Amps at 115v..  This side discharge, 2" x 2" mbt which would measure about 3" edge to edge on the threads,...