1283 results for 'pump union manifold kit'

Pneumatic tubing roll measuring 100 feet in length with 1/8" Inside Diameter and 1/4" Outside Diameter dimensions. Designed for connecting air switches, pneumatic control buttons, air-activated...

IMPORTANT: This original part has been discontinued. When you place your order, you will receive a functionally equivalent 6-spoke design cap in Dark Graphite Gray as a direct replacement for the...

The Potter & Brumfield T-92 relay is an industrial-grade DPST-NO (Double Pole Single Throw – Normally Open) switching relay designed for 30 amp loads with an 18VDC coil, engineered for demanding spa...

This Balboa VL600S 6-Button Control Overlay provides a direct replacement for worn or damaged topside labels on dual-pump spa systems with lighting. Designed for electronic topsides, this...

This is a female 4-pin AMP connector rated for 20 Amp applications. Designed to mount on the control board side within the control box, this connector accepts the male AMP cord from pumps, blowers,...

Dual pole electrical contactor for spa systemsCoilContact240 VAC30amp resThis Products Unlimited double pole contactor is engineered for reliable switching in hot tub and spa electrical systems...

Electrical relay switch - Double pole configurationCoil VoltageContact Rating120 VAC50amp resThis Products Unlimited dual pole contactor serves as the electrical relay that controls power flow in...

Replacement jet body designed for Pentair American Products Luxury Micro jets featuring a (2) tab mounting system for secure internal installation. This component requires a 1 5/8" shell opening and...

This combination temperature and high limit sensor assembly is engineered for standard Balboa 4-pin control systems (excluding M-7 configurations). The set features curly finger-style connector ends...

This part is a Standard Balboa Heater M7 Sensor with a 31" wire found in Jacuzzi Premium J series 2016 to current.    Application Balboa Water Group Sensor Diameter 1/4" Wire Length...

This reducing PVC tee fitting features three slip connections: two 2-inch openings and one 1-inch opening, designed specifically for hot tub and spa plumbing applications. The 2"s x 2"s x 1"s...

This Wet End is a 2" x 2" 3.0HP 48 or 56 frame Ultimax Vico® that would normally be found an a 230V pump with 12.0 Amps High speed there are no 115v versions of this wet end..  This side...

This listing includes (2) Air Bleeder Valve Water Nozzle Wall Fittings designed with a 3/8" barb connection. These fittings are commonly installed in hot tubs and spas to purge air from the pump...

This complete Vico® Ultimax 4.0HP wet end with 2" x 2" connections for 48 or 56 frame motors is designed exclusively for 230V pump configurations running at 14.0 Amps on high speed - no 115v...

This 2" slip x 2" spigot gate valve features unibody Magic construction rated for 100psi. One end accepts a 2" pipe or fitting with approximately 2 3/8" inside diameter (spigot side), while the...

Replacement stationary switch designed for installation in select A.O. Smith, Century, and Regal Beloit motor models. This essential motor component measures approximately 2 inches wide, 2 1/2 inches...

This 5 pin female AMP connector rated at 20 Amp serves as the control pack board receptacle designed to accept male AMP cord connections from pumps, blowers, and various spa accessories.Typically...

This genuine replacement foam-style temperature sensor for Cal Spa M7 heater systems fits 7000 and 9000 series hot tubs. The assembly includes the sensor element, attached wiring, and connector...

This Balboa M7 heater temperature sensor is a complete replacement assembly featuring integrated wiring, 2-pin connector, and screw-down cap. The 12 inch sensor with 1/4 inch fitting does NOT include...

Auto-Reset Thermodisc Surface Mount Hi-Limit Switch - DPST Configuration with Screw Terminals (No Capillary Tube)This thermal safety device mounts directly onto your spa heater assembly to monitor...